Arduino/Adafruit stepper control
||...for a Arduino and a Adafruit v2.0 motor shield controlling a Adafruit Stepper motor.
The program would work as follows:
Push button (a first time)
LED turns off and...
Push button (a second time)
LED turns off and the motor moves clockwise 50 steps and stops (release)
||Oct 19, 2013
||Oct 19, 2013Ended
Arduino Stepper Control
||...simple arduino sketch that will control the movement of a stepper motor on button press by a set number...momentary button switches.
Button 1 advances the stepper by a set number of steps (a variable to be input...by me)
Button 2 advances the stepper by a set number of steps (a variable to be input by me)
||C Programming, Arduino
||Mar 11, 2013
||Mar 11, 2013Ended
Arduino Stepper control with I/O logic
||Using an Arduino UNO or Leonardo develop a program to do the following:
On power up drive a stepper motor...move the stepper motor a set amount of steps AWAY from home position at max speed
On fall of the same trigger...move the stepper motor back to home position at max speed
1. Button attached to input
||Electronics, Microcontroller, C++ Programming, Arduino
||Oct 23, 2013
||Oct 23, 2013Ended
Arduino stepper motor controller
||...order to control four stepper motors with switches and a selector switch.
[Removed by Freelancer.com Admin]
||Aug 21, 2012
||Aug 21, 2012Ended
||...project: Arduino to control various stepper motors (from one to 25).
||May 15, 2013
||May 15, 2013Ended
Arduino stepper motor control: Sketch and circuit
||...rotate a stepper motor to (and then hold at) any one of six positions (60 degrees, 120, 180, 240, 300 and...switches, the stepper will rotate to and hold the corresponding position. On release of that switch, stepper...closed, the Arduino also should close a 5-volt relay and keep it closed for an additional 5 seconds after the
||Electronics, Arduino, Circuit Design
||Jul 19, 2013
||Jul 19, 2013Ended
Stepper Motor controlled through Arduino board by joystick
||...that can control 2 steppers with a joystick using an Arduino board . I attach photos of the boards . I'm
||C Programming, Arduino
||Apr 25, 2013
||Apr 25, 2013Ended
Private project or contest #4573468
||May 30, 2013
||May 30, 2013Ended
stepper motor_touch screen_data logging
||...need an arduino project. i want to control 2 stepper motors. i want to use touch screen and need to log
||Apr 10, 2013
||Apr 10, 2013Ended
Arduino coding, programming
||...consisted of 4 stepper motors, few sensors and controled by arduino mega.I need 5 different sketches to be combined...particular button on remote control is pressed. For your job cost evaluation below are the sizes and short...Motor (stepper motors move to home position checking home position sensors)- 8 kb. Will be used when code
||PHP, C Programming, Software Architecture, C++ Programming
||Mar 15, 2014
control Arduino from webside
||...specific arduino and turn the light on/off by clicking button .
with source code.
||PHP, Website Design, Graphic Design, HTML
||Sep 25, 2013
||Sep 25, 2013Ended
atmel stepper programming for AT90S2313
||...basic stepper control routine, must be clearly commented and this will lead to more coding with slighter...for the stepper, a dip switch as input (four lines) is used to control the stepping sequence and two normal...key push button for increase and decrease of the speed the at which the sequence is running.
||Engineering, Electronics, Microcontroller, Embedded Software
||Feb 21, 2011
||Feb 21, 2011Ended
Private project or contest #1346027
||Microcontroller, Electrical Engineering, PCB Layout, Arduino
||Dec 17, 2011
||Dec 17, 2011Ended
Stepper Motor and PIC design
||...programmable stepper motor control system.
The requirements are:
1. 4 button Input.
2. Small but powerful...powerful stepper motor equivalent nm of a mini drill/driver on low torque.
3. Programmable chip in C.
||Electronics, Microcontroller, Electrical Engineering, PCB Layout
||May 17, 2011
||May 17, 2011Ended
ARDUINO UNO Rev3, 360 degrees Photo table control with stepper motor.
A turntable with...with stepper motor controlled by arduino uno rev3 USB. The arduino is programmable by computer and can:...for 200 stepper or 1 to 400 with a 400 stepper motor. If we want 50 pictures it need to step 50 times to
||Feb 26, 2014
||Feb 26, 2014Ended
recompile an open source project
||...have an arduino software including stepper motors and time lapse.
want to add a function(manual use like...like button control) and delete another function.
||Electronics, C++ Programming, , Arduino
||Nov 19, 2013
||Nov 19, 2013Ended
Simple Arduino sketch & circuit
||ROTATE STEPPER TO ONE OF SIX POSITIONS:
Program Arduino to rotate a stepper motor to one of six fixed...disengaged, the stepper will return to a "resting" position. I have a duemillanova and a motor control...and the stepper. Need the program and circuit diagram. Thanks!
||Feb 12, 2012
||Feb 12, 2012Ended
control a LASER Set scanner Galvo 30kpps + 2 stepper motors with arduino - repost
||control a LASER Set scanner / Galvo 30kpps + 2 stepper motors with arduino
We need to develop a system...system to control a LASER Set scanner / Galvo 30kpps with an Arduino and 2 stepper motors.
the galvo system...the 2 stepper motors between the projection of 2 slides...
The parameters for timelaps and configuration
||Jun 19, 2013
||Jun 19, 2013Ended
||...using stepper motor.
The project goes like this
(1)pic16f877a 20MHz crystal oscillator
(2) Using...using 3 button to control stepper motor
(a) button A- stepper motor clock wise ( increasing speed)
(b)buton...(b)buton B- stepper motor counter clock wise ( decreasing speed)
(c)button C- interrupted that will show stepper
||Electronics, Microcontroller, PCB Layout
||Jan 4, 2012
||Jan 4, 2012Ended
Simple Arduino counter using solenoids and step motor
||...want a stepper motor to control 3 solenoids 12-24v in like fashion to the video. I want the project to...though an Arduino Uno with a visual interface of the progess of numbers. I want both a momentary button to...debounce button to pause the progession. Similarities between the video and the project i want: 3 solenoid
||Aug 20, 2012
||Aug 20, 2012Ended