Msp430 jobs
I hope you are good. I have read your description carefully and understand everything. I’m Electronics engineer who have 25 year experience on analog design, renewable energy, power electronics, motor control, microcontroller coding and PCB design. I have used Arduino, PIC, MSP430, C2000 and STM32 for 8 years. I have developed several codes by using their IDE and compilers. I know all principles of them. And I can do microcontroller simulation by using Proteus. Proteus have microcontroller model and peripheral components to simulate the code. The code can be debugged by using COF file also. Simulation result is same with real time application.
I hope you are good. I have read your description carefully and understand everything. I’m Electronics engineer who have 25 year experience on analog design, renewable energy, power electronics, motor control, microcontroller coding and PCB design. I have used Arduino, PIC, MSP430, C2000 and STM32 for 8 years. I have developed several codes by using their IDE and compilers. I know all principles of them. And I can do microcontroller simulation by using Proteus. Proteus have microcontroller model and peripheral components to simulate the code. The code can be debugged by using COF file also. Simulation result is same with real time application. I have 8 year experience on Arduino and know all principles of it. I’m using Atmega chip instead of Arduino board as a platform...
Seeking an experienced firmware developer for an in-depth review of my TI MSP430 device's source code. Mainly, the device's code is used for controlling hardware components. Key Responsibilities: - Perform a thorough review of the source code, focusing heavily on input/output handling and interrupt handling. - Optimize the code to deliver better performance and efficiency. - Enhance code clarity and maintenance for future developments. Ideal Candidate: - Proficient in Assembly Language and C. - Extensive experience in firmware development and code optimization. - Good understanding of TI MSP430 architecture. Your contribution will enhance the functionality and life cycle of the hardware components. Looking forward to your expertise and guidance.
...am sourcing an engineer to prepare a sensor the size of a CR20232 battery. The sensor needs to log the duration of a tile more than 70 degrees and needs a tack switch to log when the sensor is attached and when it is detached to bottles. The size max is the dimension of the battery and the thickness will be that of the thickest part of the pcb/component. The chip probably best for this is the MSP430 and the RF should be 433 mhz to a receiver that will be may 10 meters distant. The receiver needs to transmit the received sensor data to a cloud server via data SIM. The tilt sensor probably best will be an accelerometer but it needs to go into deep seep with nearly zero current draw unless it is tilted when the tack switch is 'on'. The sensor cost is very critical since...
The task is to check the code in the MSP430 to check the accuracy of data which comes from the GNSS Modul (Ublox) which is connected to the MSP430 via I2C. There is probably an error in the code which leads to false position values. Therefore the code has to be checked and to be corrected. It seems like the error is somewhere between the interface I2C and the Board.
I am an EE engineer. I have lots of experience designing both analog and digital circuits. In the field of simulation and PCB design, Proteus, PsPice, KiCad, and Eagle are softwares I have expertise in. I also have expertise with lots of past projects and examples in Embedded design for microcontrollers. Some of the MCUs I have worked with TI MSP430, PIC, Arduino, nordic semiconductors (i.e nrf52840), STM, MAX, etc. I am able to program devices using both Assembly language and C/C++ (both procedural and OOP). *for STM and nrf controllers Mbed OS could be one of the choices for programming the MCU. I have done lots of projects in the field of wireless communication and IoT using different wireless communication protocols like BLE, RF, WiFi (Cloud), etc. In the field of bit streami...
I'm looking for an experienced firmware developer to create a scaffolding project demonstrating the following functionality on the MSP430F6736IPZ. 1) Flashing firmware onto MSP430 using the UART BSL from a secondary microcontroller. Ideally the microcontroller would be a ESP32 of some type, but C code library demonstrating this functionality running on a PC via USB-UART cable is also acceptable, as well as any needed elements from Code Composer. 2) Implement protobuf communication onto the UART of the MSP430 that will be used to allow the two micro controllers to talk to each other under normal operation. The protobuf specification is already complete and will be provided upon selection of the applicant. No functionality beyond the uart interface is required, just impl...
Need an expert who have expertise in PLC on MSP430. More details will be shared over a chat
Looking for someone who can help with Creating a program in IAR Workbench for MSP430 It could be a scoring board Or a thermostat
We are producing a device based on msp430F5504. We almost finished to design the circuit and PCB. We are looking for someone who can write the firmware for that. I will share the circuit diagram with the candidates.
We are producing a device based on msp430F5504. We almost finished to design the circuit and PCB. We are looking for someone who can write the firmware for that. I will share the circuit diagram with the suitable candidate.
From faultly device i need to read microcontroller "m430f2132" and program newone. Probably security fuses are blown.
We are looking for experienced C developer for microcontroller: Development Tools and Environments: TI MSP-FET430 Flash Emulation Tool (FET). The FET is the program development tool for the MSP430™ ultra-low-power microcontrollers Main CPU Application: MSP430 series The following environment: C coding over IAR compiler for TI MSP430 (EW430-MB) for MSP430 micro-controller.
Hello, I would like to hire intermidiate or novice programmer for a project based on MSP430. Furthur details will be discussed afterwards.
Implement the MQTT project with MSP430 using the ESP8266-01 module, I have 100$ and I want it in 7 days, DO not need a PCB design.
Hello, I am looking for a smart and talented assembly programmer who is familiar and has a MSP430 to create a simple calculator. I am looking for a assembly programmer to create LED colors :Red Green Blue on the msp430. Looking for someone who can do it quick. Thanks
Hello, I am looking for a smart and talented assembly programmer who is familiar and has a MSP430 to create a simple calculator. I am looking for a assembly programmer to emulate multiplication, division, modulo, and power since the msp430 does not have these functionalities in the controller's instruction set. Looking for someone who can do it quick. Thanks
Small MSP430 project starting from an Embedded OS, I provide documentation and information. It is a really small project where we need to implement some tasks.
i need someone good in Microcontroller programming MSP430 and I2C peripherals, assembly and c language. i will provide more details in the chat.
We are working on an RaspberryPI application in python 3 which communicates with MSP430 device over I2C protocol. Every thing works as expected with Raspberry PI powered through regular USB. Issue We want to power RaspberPI using GPIO using pins 2 and 4 for 5v and GND. When power using GPIO RaspbianOS work fine with no lightning bolt on top right or low voltage warning however our python application doesn't communicate.
Hi Muhammad N., I need a project written in IAR for Msp430 (msp430f149) to read values from hx711 and send them to serial uart1. Can you help?
Hi there. I have code written for msp430 which interacts with a modem through serial. I would like to change the code to work with an ESP32. The modem just sends integers as commands and the libraries handle those responses. From what I can understand the main changes are the GPIO definitions and the eeprom to allow saving data. Would you be interested in helping or knowing more?
Hi Akhil. I've been working with WirelessHART protocol recently and I have some WirelessHART modules and code libraries written for msp430. I'm wondering if you might be capable to help modify the code to work with ESP32 as the microcontroller? Potentially after get it working on stm32 blue pills. regards, Gary
Hello. I have code written for a msp430 which talks to a modem through UART. I'm wanting to convert the code to work with ESP32. main issues are the GPIO definitions and using eeprom for saving data. there are about 6 include files, some of which have references to the msp430 and some just handle calls to and from the modem. Does this sound like something you could help me with? regards, Gary
Hello. I have code written for a msp430 which talks to a modem through UART. I'm wanting to convert the code to work with ESP32. main issues are the GPIO definitions and using eeprom for saving data. there are about 6 include files, some of which have references to the msp430 and some just handle calls to and from the modem. Does this sound like something you could help me with? regards, Gary
Hi, I need someone who can complete a project which is a simple clock that needs to be displayed on a 7 segment display using msp430g2553 board. The programs needs to be done in IAR workbench.
This is an interface to the popular ESP8266 wifi module. These little modules are incredibly handy if you are going to pull small pieces of information from a HTTP server. It supports both TCP and UDP connections, and it can setup up to 4 server connections.
I need the following project to be done: Connect an MSP430FR6989 to an ESP8266 Wifi module and write code that connects the Wifi module to the internet.
Hi Usman, I tried replying to your message on the RPi, MSP430 project but for some reasons, the message is not getting delivered to you. Could you please detail out the requirement?
The task is the following: write a program for the MSP430FR6989 that outputs an analog signal that varies from 0 to 3.3V.
I need to implememt PPM modulation scheme using Code composer studio. I need help for this project
Hello Ali , I have a microcontroller based project that require the use of the (MSP430) board and the whole idea of it is basically the board has to take data from humidity and temperature sensors then if the numbers obtained reach a certain range it would send a message via Bluetooth to a mobile phone (I have bought the HC-05 and HM-10 Bluetooth modules but not sure which one to use) my part is hardware and Bluetooth so it’s not the full thing. Budget is negotiable.
Hi Sardar Hasnain A., I noticed your profile and would like to offer you my project. We can discuss any details over chat. I have a microcontroller based project that require the use of the (MSP430) board and the whole idea of it is basically the board has to take data from humidity and temperature sensors then if the numbers obtained reach a certain range it would send a message via Bluetooth to a mobile phone (I have bought the HC-05 and HM-10 Bluetooth modules but not sure which one to use)
Hi majidabdi, I saw that you have experience using the MSP430 microcontroller. I have no experience with this module especially the MSP430FR4331 using the CCS compiler. What I want is basically to have the project bases files to be able to communicate in i2c, uart. DM if you want more info about the Regards!
I have an TI MSP430 Application in IAR Studio. Please review and if interested please get in touch.
I am asking for someone , who can develop a nesc program for TelosB device . I have connected this device with an spectrometer external sensor (AS7265x) through the connectors on the Telosb. I need that this program, running on MSP430 of Telosb, can read the data from the spectrometer and send back to my PC. The Telosb is connected to the PC through the USB port. See the photos for clarification.
Hi We're looking for someone with coding experience with the MSP430 MCU Series by Ti.
I am asking for someone , who can develop a nesc program for TelosB device . I have connected this device with an spectrometer external sensor (AS7265x) through the connectors on the Telosb. I need that this program, running on MSP430 of Telosb, can read the data from the spectrometer and send back to my PC. The Telosb is connected to the PC through the USB port. See the photos for clarification.
I am asking for someone , who can develop a nesc program for TelosB device . I have connected this device with an spectrometer external sensor (AS7265x) through the connectors on the Telosb. I need that this program, running on MSP430 of Telosb, can read the data from the spectrometer and send back to my PC. The Telosb is connected to the PC through the USB port. See the photos for clarification.
Communication using PPM modulation scheme using MSP430
Communication using PPM modulation scheme using MSP430
I am asking for someone , who can develop a nesc program for TelosB device . I have connected this device with an spectrometer external sensor (AS7265x) through the connectors on the Telosb. I need that this program, running on MSP430 of Telosb, can read the data from the spectrometer and send back to my PC. The Telosb is connected to the PC through the USB port. See the photos for clarification.
Hi, Trying to measure voltage and it's not very accurate so looking for someone to improve the accuracy. Code is written in C for the microprocessor and pulling information from a battery charger's ADC inputs. Microprocessor: MSP430F247-TPMR Clock: ECS-160-20-30B-TR ADC circuit and relevant existing code is attached (voutsense is connected to P6.1/A on the MSP430)
We would like to have code for MSP430-4133 MCU which would read data over I2c/SPI and send that data over serial every 20 seconds. This device must run for 1 years on 1000mAh battery.
This project is an introduction to embedded system with various tasks including working with LEDs, accelerometer, temperature sensors,.... this project will require a working simulation and codes.
Using a PT1000 and accelorometer to measure temp and movement. Transmit these data using RF to a computer. Multiple MSP430 will be connecting to the computer so system needs to differentiate each temp/acc sensor
