Velleman k8055 jobs
...com/products/rmp3 https://www.amazon.com/Cylewet-ISD1820-Recording-Playback-Loudspeaker/dp/B01MS2N1UJ/ref=sr_1_4?dchild=1&keywords=ISD1820+Voice+Recording+Playback&qid=1616336691&s=electronics&sr=1-4 Input #3: This input will replace the current device we have in place: https://www.amazon.com/Velleman-VM144-Telephone-Detector-Output/dp/B001IRQAZ8/ref=sr_1_3?dchild=1&keywords=velleman+telephone&qid=1616429989&sr=8-3 The input signal will be a telephone ringer from a telephone line. The Arduino will close a circuit as our amplifier has a built-in ringer. Freelancer to provide: Complete program An electrical diagram (simple sketch) will be required Complete support until testing phase is complete...
Want to ran a nema43 stepper motor with Velleman VMA406 relays
Target is to build a simple desktop application which reads text from the chat window and controls the Velleman VM110 USB interface card module. Libraries and example code for the card is available here: Application will have a simple UI (see the attachment), where user can: 1. Setup a "Nickname" which will be monitored on the active chat window (chat window which is used by the performer/model) 2. Setup few parameters for Velleman board control 4. button to set (take in use) the new values 5. Button for start and stop the application Use-case: Video chat model can choose a Nickname from the chat window and fill it in to the application UI (see attachement). After starting the application it starts to monitor
Hi, I need someone that can create a (or adjust existing) case for an arduino project that I can print with my 3D printer (velleman K8400). I want a case in this style: :626368 Including port & button cutouts etc, and I want some text engraved on the lid. There are 3 parts in my stack: Top: GSM shield () Mid: Ethernet shield Bottom: Uno The link () is a good starting point, since the two lower parts are the same. Only place for the GSM shield should be added (but GSM shield is a bit bigger then the rest). I can provide exact measurements of the parts. Thanks
The job is about a simple programming. It may be done with C++, E-Prime, LabView or other languages. It is about steering LED diodes and small vibration motors: I also have the following USB interface card by Velleman, if it is needed: Together 4 LEDs and 4 motors are to be controlled. Simulatenously in one trial one LED and one motor are on for a short time. 4 different combinations are possible (e.g. motor 1, LED 2, motor 3, LED 4). They simply have to be turned on and turned off. After each trial a response with a two button response panel is made
We need a software package designed to operate on both Windows xp 32bit and Windows 7 32 bit that will control a Velleman K8055 board. Reference: This software will be full screen including a company logo that will be provided. We will provide the successful freelancer a basic layout of all screens. Software must look at digital inputs of the board and display text on the screen for each input. There must be a menu built in that allows certain digital inputs to trigger one of the 8 outputs whenever the input is high. There must also be configurable buttons on the screen to turn other outputs on. This software will be ran on a touch screen so buttons must be large enough for either mouse or finger. When button is clicked
i need someone have experience with Visual Basic 6 use interface card k8055 my code has 2 input and 3 output .i want form him write report for it i prefer how now k8055
I need (1) a circuit diagram to connect Sensirion SHT15 digital humidity and temperature sensor to my Velleman K8055 interface board and (2) some assistence via e-mail during programming (I'd do it myself, just need some guidance) and testing.
I have some cards with switches (Velleman K8056) that are controlled via RS232 and I want a piece of software that can time schedule those. I want it to be in VB and I want to have day-week-month schedule options.
We have a Velleman K8062 USB DMX lighting controller () and need someone to use the SDK to develop a program for controlling the interface. The SDK file can be found here: We don't mind which language is used (Included in the zip are examples in C++ Builder, Delphi, VB.NET and Visual Basic). Our main requirements are: * There be 16 sliders on view and a slider along the bottom to go across to the full 512 * A system for setting the delays between scenes * The ability to save the DMX scenes in a file format, usually these are very simple text based files I believe * A master controller to move all of the switches at once If you have any queries
I am looking for a small application for a magnetic card based door entry system, that will validate the card details against a simple text file type database, then call a DLL to operate a USB relay board to open the door lock. The card reader presents data as a standard keyboard device. The USB relay board is a Velleman kit. The app will be run from a dedicated Fujitsu Stylus tablet. The app should sit in the foreground and just monitor the keyboard entry and accept the string, the final character being a line feed or enter. Validate against the database. Open relay if valid for 10 second. Possibly open a 2nd relay for 30 seconds. Then reset. A soft button should be present to open a data entry window to suspend entries in database or add new entries. a new e...
...and a short bid of code that I have written should give you an idea of what I want done. Using the kdtele software is not neccessary, will accept any coders code. ## Deliverables Here is some more information on what is to be done. A piece of experimental lab equipment that generates on/off states and several analog signals is connected to : <> This interface board routes the data coming from the equipment to a dedicated Pentium 1 notebook running Win 98. This part works fine and has been for several months. Every once in a while user intervention on the equipent must be preformed. This intervention is done through the notebook which commands the LPT to change the outputs of the K8000 interface board which actuates
Witam Dziękuję za zainteresowanie sie zleceniem. Pisze program na zaliczenie, przedmiot to Programowanie, rok 3, uczelnia nieistotna. Program ma za zadanie kontrole sygnalow naplywajacych poprzez port USB za pomoc tego oto urzadzenia: wiŕcej informacji na ten temat: google i "velleman p8055" W zamysle ma to byc taki mini-alarm domowy. W tej chwili program za pomoca biblioteki .dll umozliwia zczytywanie/wysylanie danych, i to dziala. Co jest do zrobienia: - nazwy wejsc/wyjsc powinny byc edytowalne w oknie [USTAWIENIA] i nazwy te zapisywane w tabeli SQL - dodatkowa tabela powinna byc dla uzytkownik/haslo do logowania do programu, zmiana danych w tej tabeli dodatkowo powinna byc zabezpieczona ponownym wpisywaniem hasla - nastepna
