offline
Last seen: Mar 11, 2014 8:17 AM EDT
Hire Me!
Rate: $10.00 USD/hour
Follow Invite to Project
 

alekol

1

Username: alekol

  • Has made a deposit.
  • Has verified their email address.
  • Has completed their profile.
  • Has verified their secure phone number.
  • Verified
  • Payment is verified.

Location: Khmelnitkyy, Ukraine

Member since: November 2011

Reputation:

4.9/5

(2 reviews)

4
[see more]

No user has recommended this freelancer.

My projects:

  • $700.00 USD
    5.0
    Profile image for Seller tedkim

    tedkim

    Dec 19, 2013

    He is really good man with quick response and good efforts for better solutions. I always hire him again.

    Project Description:I want to design a small and cost effective microcontroller board for 2 gases control. I sketched schematic diagram and flow charts roughly, which are attached as zipped file. I need very cost effective board in material cost...
    [more]
  • $350.00 USD
    4.8
    Profile image for Seller tedkim

    tedkim

    Jun 16, 2013

    Alex is really good man. He did not disappoint me. He has good skill and technology, especially kindness. I want to work with him again. He will not disappoint you. Hire him.

    Project Description:I have made a project and need to modify them now. Let me explain what function my project do. I have 18 sets of ATMEGA128A microcontroller boards located widely in very noisy areas due to near heavy induction motors and inverters...
    [more]
    alekol has not completed any projects.
  • $500 USD In Progress

    This project is the upgrade and split of past project.I want two types of board. One is 1ch premium board and the other is 4 ch Economic board.Other condition will be sent by email after decision of engineer.

    [more]
  • $300 USD In Progress

    I post project of magnetic levitation system.Please see attached image file of the layout.It needs 4 electric magnetic coils to lift up the plate at the corners.If permanent magnets are needed, they can be attached.I will put the weights on the plate and the weight will be varied between 50g and 500g.And I want to control the lifting heights by microcontroller such as ATMEGA series. The heights will be between 0mm and 20mm and should be controlled individually. The size of plate is 200mm * 300mm.And another important matter is very little heat on the magnetic coils.Final products should be:;1. schematic and pcb design files in full2. 1 set of complete set of system.3. 1 set of completely mounted and tested board.4. 5 pcs of bare pcb.Please describe the full experiences of magnetic levitation system.

    [more]
  • $30 USD In Progress

    Sorry, I closed the projects and now i cant talk to you.I assume we need to have an open project to continue to communicate.I need to make sure you got your payment.Thanks

  • $1000 USD Aug 27, 2013

    вытащить прошивку в обход паролю

  • $1333 USD Jun 27, 2013

    [Project]GSM/GPRS Tracker with sensors for Low Power Application. Module will be dormant most of the time, wake up periodically to check for an incoming SMS, and if an incoming SMS is there, answer with the location of the tracker. [Components]- GSM/GPRS + GPS (SIMCO908)- Compass (AK8975)- Accel (LIS331DLH)- Battery Level Monitor (LTC2942-1)- Microcontroller TBD- GSM/GPRS + GPS Antenna TBD[Requirements] Please see attached block diagrams.[Taks + Milestones]1- Discussion on Components and FW functionality. Draw by hand HW block diagram. Schematic Capture. Board Layout. (MILESTONE1 $ TBD)2- Spin Two Boards, Debug (MILESTONE2 $ TBD)3- Code FW discussed in basic FW block diagram in (1). (MILESTONE3 $ TBD)[Deliverables]- Schematic Capture- Board Layout- Source Code for FW- PCB (physical board, HW)[How to Bid]Place a total bid and indicate three milestone payments as indicated above.

    [more]
    alekol does not have any open projects.
    alekol does not have any work in progress.
[see more]

Portfolio

[see more]

Résumé

Education

Specialist

National Aerospace University -'Kharkiv Aviation Institute'

1994-2000