diegosalazar

My projects:

• mikroC for dspic, pic24f, wav file .,sd card

  $60 USD
  5.0
  

  sherazi11

  Jul 7, 2012

  “ A+++ work, complete with additional support material, would like to work again and again and again. :)A+++ work, complete with additional support material, would like to work again and again and again. :) ”
  Project Description: I want someone to code using MIKROC for dsPIC . details : PIC waits for a sting from serial port, based on the string the PIC would look for a .wav file and play it from the SD Card. I would...
  [more]

diegosalazar has not completed any projects.

• Firmware Programming for Pic32MX series Microcontroller

  £100 GBP In Progress

  i have a schematics for PIC32MX460F512L in which a camera is attached at one port and a wifi device is attached on the other port. the camera will take grey scale photos and send it to the external memory location which is also attached to a port in the schematics. after taking photos for a minute, the microcontroller will output the data through the wifi device. i need a Proteus simulation and a C Program code that will work on the Proteus simulation so that confirming that the code is right and working.i need the job done in not more that 3 days.i have a schematics for PIC32MX460F512L in which a camera is attached at one port and a wifi device is attached on the other port. the camera will take grey scale photos and send it to the external memory location which is also attached to a port in the schematics. after taking photos for a minute, the microcontroller will output the data through the wifi device. i need a Proteus simulation and a C Program code that will work on the Proteus simulation so that confirming that the code is right and working.i need the job done in not more that 3 days.

  [more]

• Mesh network wifi module

  $1666 USD 8 days ago

  Hardware design and software development needed for a networked wifi module. Each module will provide a wifi hotspot and be networked together with other modules via a mesh network. Internet connectivity will be provided by a laptop computer connected to the mesh.If preferred, the inter-module mesh connectivity can be implemented via non-wifi (e.g. zigbee), but in this case, the module would still need 802.11 wifi for the hotspot.The modules should be as low cost as possible and should be physically small (for example the system should fit in a 50mm cube) and run from standard rechargeable AA or AAA batteries.The module should have GPS capability, and a location report will be triggered remotely via the laptop.The processor used should be capable of being extended for simple GPIO.In your proposals, please specify what hardware you would suggest for this purpose. Specify the approximate hardware cost and power requirements of the module components.Preferably software will be written in C. For the software, please specify what languages and tools you would use and what components of the software you will implement are off the shelf or will be written from scratch. Please detail experience you have in this area and timescales for delivery.Thank you for your time and we look forward to your proposals.Hardware design and software development needed for a networked wifi module. Each module will provide a wifi hotspot and be networked together with other modules via a mesh network. Internet connectivity will be provided by a laptop computer connected to the mesh.If preferred, the inter-module mesh connectivity can be implemented via non-wifi (e.g. zigbee), but in this case, the module would still need 802.11 wifi for the hotspot.The modules should be as low cost as possible and should be physically small (for example the system should fit in a 50mm cube) and run from standard rechargeable AA or AAA batteries.The module should have GPS capability, and a location report will be triggered remotely via the laptop.The processor used should be capable of being extended for simple GPIO.In your proposals, please specify what hardware you would suggest for this purpose. Specify the approximate hardware cost and power requirements of the module components.Preferably software will be written in C. For the software, please specify what languages and tools you would use and what components of the software you will implement are off the shelf or will be written from scratch. Please detail experience you have in this area and timescales for delivery.Thank you for your time and we look forward to your proposals.

  [more]

• Electrical and PCB layout design: MCU + USB + Stepper controllers

  $825 USD 19 days ago

  Required/Applicable Skills:1) knowledge of manufacturing capabilities2) Ability to make Atmel controllers3) Ability to drive stepper motors with long term reliability without an integrated circuit driver4) connect USB by virtual connection to Atmel (arduino)We are looking for a really good PCB and electronics designer to be on call for us to do tasks that will take less than a week from time to time. We want someone with experience in keeping costs low and designing for bulk manufacturing and assembly.MUST understand stepper motor control and be able to make one using multiple FETs to achieve a low target price.Other continous tasks and assignments are available.Only apply if you speak English well.Required/Applicable Skills:1) knowledge of manufacturing capabilities2) Ability to make Atmel controllers3) Ability to drive stepper motors with long term reliability without an integrated circuit driver4) connect USB by virtual connection to Atmel (arduino)We are looking for a really good PCB and electronics designer to be on call for us to do tasks that will take less than a week from time to time. We want someone with experience in keeping costs low and designing for bulk manufacturing and assembly.MUST understand stepper motor control and be able to make one using multiple FETs to achieve a low target price.Other continous tasks and assignments are available.Only apply if you speak English well.

  [more]

• Firmware in MikroC for PIC 16F628A, frequency converter

  $77 USD 20 days ago

  I need firmware for a 16F628A with can receive a pulse frequency through the external interrupt, multiplies it by variable 'x' and uses the result to generate a new pulse.I need firmware for a 16F628A with can receive a pulse frequency through the external interrupt, multiplies it by variable 'x' and uses the result to generate a new pulse.

• EAGLE Scripting for PCB Design

  $150 USD Mar 2, 2013

  We need to create a PCB layout for a wireless power transfer based in a fractal antenna.The PCB need not be fabricated, we just need an eagle script.The script will input:Mil spacing, PCB dimensionsnumber of levels of recursion.We are seeking a sierpinski fractal antennahttp://www.ece.iit.edu/~pfelber/fractalantennas.pdfshows what we have in mind.Do not bid higher than the maximum price of the project.Thanks! - DLP.S. this may result in a KS project...I have done these kinds of KS projects before at:http://www.kickstarter.com/projects/2006771911/the-arduino-dsp-shield/We need to create a PCB layout for a wireless power transfer based in a fractal antenna.The PCB need not be fabricated, we just need an eagle script.The script will input:Mil spacing, PCB dimensionsnumber of levels of recursion.We are seeking a sierpinski fractal antennahttp://www.ece.iit.edu/~pfelber/fractalantennas.pdfshows what we have in mind.Do not bid higher than the maximum price of the project.Thanks! - DLP.S. this may result in a KS project...I have done these kinds of KS projects before at:http://www.kickstarter.com/projects/2006771911/the-arduino-dsp-shield/

  [more]

• ECG Signal compression Interface

  $50 USD Mar 18, 2012

  Project : ECG Signal compression Interface Description : The worker needs to come with an interface based on matlab program for ECG signals chosen from MIT-BIH and applied to compression algorithms and get the compressed signal out NOTE: All of the signals and their algorithms are ready with me the worker duty is just to design a sufficient well done interface and provide details and full description of the interface code and and work space of it .Project : ECG Signal compression Interface Description : The worker needs to come with an interface based on matlab program for ECG signals chosen from MIT-BIH and applied to compression algorithms and get the compressed signal out NOTE: All of the signals and their algorithms are ready with me the worker duty is just to design a sufficient well done interface and provide details and full description of the interface code and and work space of it .

  [more]

diegosalazar does not have any open projects.

diegosalazar does not have any work in progress.

Portfolio

Description

Related Work

diegosalazar Portfolio