Altium designer schmetic pcb jobs

Filter

My recent searches
Filter by:
Budget
to
to
to
Skills
Languages
    Job State
    9,956 altium designer schmetic pcb jobs found, pricing in USD

    This project is to be completed in Kicad software; the schematic and pcb layout. It is a 300amp motor controller for 3 phase AC induction motor. The battery voltage will vary between 3volts and 25 volts. It must be able to operate all the way down to 3 volts! Some boost circuitry will need to be designed for gate drive. There will be 6 mosfets total

    $197 (Avg Bid)
    $197 Avg Bid
    2 bids

    We have a schematic in Capture and its PCB design in LayoutPlus (using Orcad 10.3 & 15.7). The schematic has been updated and the PCB design has to be changed to reflect the change in the schematic. Footprints and pad sizes have to be updated on the PCB. PCB design itself needs to be optimized. The schematic consists of a 20 pin IC and two 8 pin

    $145 (Avg Bid)
    $145 Avg Bid
    7 bids

    PCB board designed in eagle cad. need to have couple changes made to it. very miner, have all files.

    $58 (Avg Bid)
    $58 Avg Bid
    23 bids

    I need to design a LED chaser that will be powered by a 12V battery. It needs to have a master PCB which will control all the slaves connected. The slaves will be chained together and distanced about 5 meters apart with a 4-pin connector IN and 4-pin connector OUT. Each slave will have a 12V lamp attached and switched by a mosfet. The requirement

    $273 (Avg Bid)
    $273 Avg Bid
    17 bids

    I want to take my arduino mega project to a prototype stage. The project uses these external modules: arduino mega 2560, 4 buttons (interrupt pins), ds3231 real time clock, 5 port 220v relay module, 4 RGB LED, 5110 lcd screen module. The circuit receives 12v 3A input. I would like there to be 5V and 3.3V management for the modules as required and one 24V on the 1s port of the relay. The extern...

    $63 (Avg Bid)
    $63 Avg Bid
    4 bids

    We have a very specific design we wish to enhance that requires the cirrus metering chip. We want someone to assist with design of the schematic, BOM and PCB design. Experience with metering chip preffered but you MUST be able to speak and meet deadlines.

    $25 (Avg Bid)
    $25 Avg Bid
    10 bids

    I have a problem with PCB layout. I want to hire anyone who has PCB design skill. Please contact with me.

    $11 / hr (Avg Bid)
    $11 / hr Avg Bid
    46 bids

    I need some help with selling something. Iam the manufacturer of organic waste converter of super...biogas plants and having a dealership of STP plants,I need people who market these products on percentage basis as usually these products are mandatory for clearance of BWSSB,PCB,BBMP at apartments and IT parks etc places where waste is generated more.

    $193 - $578
    $193 - $578
    0 bids

    PCB layout using Allegro/Orcad version 17.2 (Don't use 16.6) 1) Update schematic, minor changes, may include creating three footprints 2) Understand and follow the specified component placement 3) PCB layout with necessary consultation 4) Prepare design files, ready to order PCBs

    $441 (Avg Bid)
    $441 Avg Bid
    19 bids

    ...MEMS sensors feeding an analog processing chip, to an ADC to a PIC micro. we built 3 PCBs for prototype test. the first was populated and had a short. then we tested the bare PCB and there is a short that we simply cannot find. At this point, all I am looking for is help finding the short before building more. Could be a manufacturing problem, just not

    $13 / hr (Avg Bid)
    $13 / hr Avg Bid
    6 bids
    Altium help 4 days left

    Altium help needed for learning.

    $38 (Avg Bid)
    $38 Avg Bid
    2 bids

    Hi Walid, I want to design and build a pcb here in Egypt and looking for a freelancer located in Egypt in order to deliver me the final PCB. I want to build a PCB with 5 shift registers that can control 20 relays and accept 20 buttons as inputs ( total 40 pin ) to be controlled by ESP8266. It is fairly simple board but I need it as quick and clean

    $50 (Avg Bid)
    $50 Avg Bid
    1 bids
    4 layers PCB Design on Altium 4 days left
    VERIFIED

    deadline for this pcb design is 3 days. The part name CP1~CP80 is cap for power supply. Please place this parts close to IC. You should place of FCON1과 FCON3 connector is Top and FCON2, FCON4 is bottom inner layer is GND와 +5VDC The area marked FAULT - A1 is the structure that stacks up the boards of Fault-A2 FAULT - A3 FAULT - A4.

    $128 (Avg Bid)
    $128 Avg Bid
    23 bids

    Looking to have some hardware items possible changed to software to free up board space on pcb Currently have (Atmega2560 MCU)

    $492 (Avg Bid)
    $492 Avg Bid
    25 bids

    i want to learn orCAD pcb designing completely... need a guru from Chennai

    $300 (Avg Bid)
    $300 Avg Bid
    4 bids

    ...team) who is located in China. I need an electronic engineer skilled in Arduino, Raspberry Pi, WiFi, Bluetooth, PIC, PLC and professional in Electronics schematics and PCB design (Altium)–Circuit analyzing and debugging- Hardware reverse engineering - Firmware development –C++, C- microcontroller embedded system - EMC Compliance Consultancy - Test & Manufacture

    $742 (Avg Bid)
    $742 Avg Bid
    17 bids

    Multiple devices will be used in one setup (1 to +100 devices). They authenticate to the network and receive a unique ID. Use of esp32 or another uc for wifi connection to central server. Creation of server software api to communicate with all devices. API talks to an existing MSSQL database with all information about pricing, customers, ... Need to register new devices. This will assign an i...

    $3447 (Avg Bid)
    $3447 Avg Bid
    17 bids

    Build me a PCB layout with all the parts needed from the given schematics attached. I will be sending the PCB layout to the company who would make the PCB layout as well as the parts needed. *Please analyze the pdf fille attached

    $159 (Avg Bid)
    $159 Avg Bid
    46 bids

    schematic, part creation, library creation, pcb routing

    $41 (Avg Bid)
    $41 Avg Bid
    7 bids

    Design a collaborative robotic arm that has the same function like, universal robot, aubo robot, and C-15 Collaborative Robotic Arm. With control box. Similar size...With control box. Similar size and specs. (Working radius around: 1300 mm) Want a 3d file like SolidWorks. -5 difference design -Add some inside components ex-motor, PCB board

    $189 (Avg Bid)
    $189 Avg Bid
    18 bids