Filter

My recent searches
Filter by:
Budget
to
to
to
Skills
Languages
    Job State
    981 altium jobs found, pricing in USD

    I'm in the need of a PCB designer that has good knowledge on the use of Altium, to build an autopilot expansion board. Before I do so I want to verify skill and competence of the candidate, therefore I have an add on project to be used as test. The unit is a multi link transmission system, that switches across the different communication units

    $307 (Avg Bid)
    $307 Avg Bid
    12 bids

    USB Power Delivery Device Using Cypress CCG family of Ic's Knowledge of Cypress CCG is required as well as Altium and Electronic Design

    $503 (Avg Bid)
    $503 Avg Bid
    9 bids

    ...US$750 or less Expertise Required: – C – GCC – Signal Processing – Circuit Design – Knowledge of Delta-Sigma ADCs Inputs: – Altium .schdoc, .pcbdoc, .prjpcb and .prjpcbstructure files + Altium Source files – 3D Models – BOM, gerber, source files – Datasheets – Reference Docs – Actual PCB, if...

    $1140 (Avg Bid)
    $1140 Avg Bid
    33 bids

    We need to do a fairly quick spin of an 8-layer high density PCB for a wearable IoT device for dogs. Current design is in Altium project files. Requirements: --Design multi-layer printed circuit boards with high layer count, high density, high pin count and fine pitch components, BGAs as well as develop analog and high power circuit boards --Evolve

    $54 / hr (Avg Bid)
    $54 / hr Avg Bid
    21 bids

    Using altium designer, we need new PCB routing due to replacement of an electronic smd component

    $30 (Avg Bid)
    $30 Avg Bid
    26 bids

    I need a freelancer to design PCB with ALTIUM DESIGNER. I will give schematic in ALTIUM and requirements of board (number of layer, dimensions, etc..)

    $188 (Avg Bid)
    $188 Avg Bid
    11 bids

    I have designed a pcb in Altium. I need to check the pcb and create list of materials and gerber files. I need you to manage the manufacture of pcb, purchase of components (better quality, low price), assembly of prototypes, shipping and programming a stm32 microcotrolator.

    $175 (Avg Bid)
    $175 Avg Bid
    38 bids

    On-going work doing various Printed Circuit designs.

    $18 / hr (Avg Bid)
    $18 / hr Avg Bid
    9 bids

    ...acquired from and not someone who is a broker, it must be the manufacture or the manufactures authorized distributor. Lastly in designing the board, you can use Orcad, or Altium, Eagle, or if you do use some other tool, those files have to be supported by one of the sources listed, so that any future changes can be supported without the need to acquire

    $511 (Avg Bid)
    Featured Urgent NDA
    $511 Avg Bid
    19 bids

    A multipurpose PCB board that will mount on a small embedded motherboard. Your work: modifing some part from current schematics and the PCB layout (4 layers) in Altium Designer. routing some few tracks in PCB less than 2 hours of work if you are expert

    $39 (Avg Bid)
    $39 Avg Bid
    18 bids

    I want to make a small automotive PCB. Design in Altium. Micro controller will be the Atmel SAMD21 basically a striped down Arduino zero, like SAMD21 mini from sparkfun. Needs a automotive power supply 12v with protection. 2x PWM output 12v with transistor and mosfet. one source and one sink. CAN-BUS input with MCP25625, SPI to SAMD21 need a small

    $274 (Avg Bid)
    $274 Avg Bid
    43 bids

    See attached PDF before proposals. Must do the following: *Create schematic with modifications(remove connector, simplify wiring, rearrange caps) *Find/Create footprints for all symbols/components (use existing BOM on page 2) *Add one supplier link based on MFG part number for each schematic symbol (right click->Add supplier link). Digikey preferred. PCB layout not required.

    $58 (Avg Bid)
    $58 Avg Bid
    7 bids

    To modify/remove some part from current PCB (both Schema and Layout) in altium. Board Name: Toradex Ixora V1.1 Please refer below link: [url removed, login to view]

    $381 (Avg Bid)
    $381 Avg Bid
    33 bids

    See attached PDF before proposals. Take an existing Altium schematic doc and do the following: *Find/Create footprints for all symbols/components (use standard SMT sizes when possible) *Add one supplier link based on MFG part number for each schematic symbol (right click->Add supplier link). Digikey preferred. PCB layout not required, only PCB

    $100 (Avg Bid)
    $100 Avg Bid
    8 bids

    ...drive the motor from a 48v battery pack. - charging the 48v battery pack from solar panel. - Use the 220v main supply to drive the motor. The design must be done using Altium design and components can be purchased online (digikey, mouser...), If special components are used the freelancer need to provide all the information for making those components

    $371 (Avg Bid)
    $371 Avg Bid
    12 bids

    Create schematic in Altium Designer for the attached circuit. *Add pin numbers to symbols

    $63 (Avg Bid)
    $63 Avg Bid
    2 bids

    Create Altium designer schematic of attached image. One sheet only.

    $133 (Avg Bid)
    $133 Avg Bid
    2 bids

    Hello, I would like to convert Altium SCH and PCB files (attached) into Eagle CAD format with a few modifications. 1. The original schematic contains a 60-pin connector. I need one more (72-pin connector) to be added. Please use my library (attached) to add the components. It already contains the 60- and 72-pin connectors for your convenience.

    $287 (Avg Bid)
    $287 Avg Bid
    2 bids

    We have a five by six inch PCB, completed schematic and parts list (170 total SMT, through hole mix) Need PCB layout and Gerber from files This is a controller board for a touchscreen embedded controller

    $402 (Avg Bid)
    $402 Avg Bid
    44 bids