Analysis programming microcontroller jobs

Filter

My recent searches
Filter by:
Budget
to
to
to
Skills
Languages
    Job State
    3,457 analysis programming microcontroller jobs found, pricing in USD

    I want to to state of charge estimation using extended kalman fiter for battery management system. Freelancer has to develop a model with extended kalman filter i...charge estimation using extended kalman fiter for battery management system. Freelancer has to develop a model with extended kalman filter in matlab which is deployable in microcontroller.

    $76 (Avg Bid)
    $76 Avg Bid
    7 bids

    I wrote a guide in English about on the Arduino microcontroller, which is about hardware and electronics. I would like that this guide is corrected and improved by someone who masters the English language in order to correct possible errors and make it more readable and fluent. There are about 18900 words, but including many text sections with math

    $139 (Avg Bid)
    $139 Avg Bid
    21 bids

    Hi, I need a bootloader for PIC32MX795F512L Microcontroller. I already have an application, and I want to be able to remotely update it. Candidates must ask the following questions in order to be considered: Do you have some similar solution already working? What is your experience working with boot loaders? Have you worked before with PIC32MX

    $214 (Avg Bid)
    $214 Avg Bid
    5 bids

    Develop an embedded software for stm32l4 microcontroller connected to a cellular module SIM808 to connect to internet and get the GPS position information. The software project must be developed on Keil uVision5 or System Workbench for STM32. And most be based on the X-CUBE-AWS from STMicroelectronics. The final objective of the project is to send

    $279 (Avg Bid)
    $279 Avg Bid
    9 bids

    To read DLMS Meters using microcontroller preferably using C

    $360 (Avg Bid)
    $360 Avg Bid
    5 bids

    To read DLMS Meters using microcontroller preferably using C

    $248 (Avg Bid)
    $248 Avg Bid
    7 bids

    ...on (2min) and off (1min) then on again, then use the two sensors to turn the system off once humidity value set or soil moisture value set is reached hence sensored by microcontroller. But once I integrate the library and codes for everything it does not function the way I want it to. To be turned on by the RTC circuit then off by initiating the two

    $24 (Avg Bid)
    $24 Avg Bid
    10 bids
    $379 Avg Bid
    37 bids

    Hi, I am looking for someone who can recreate the OBD2 Bluetooth device using the STN1110 MicroController. ELM327 - [url removed, login to view] STN1110 - [url removed, login to view] The ELM 327 is an older version we would like recreate a more robust version of the same using the STN1110. I am not

    $100 (Avg Bid)
    $100 Avg Bid
    5 bids

    I need a software developer experienced with microcontroller software development in accordance with IEC/UL 60730 standards. We design, develop and provide advanced electro-mechanical systems to the appliance industry.

    $16047 (Avg Bid)
    $16047 Avg Bid
    9 bids

    ...like: I have to connect NXP PN532 reader (link below) using UART interface (I think it is more preferable than I2C or SPI interface because of its simplicity) with PIC microcontroller, which should be modelated in Proteus. Connection between PN532 and PC should be made with help of RS232-USB adapter, as far as I undersand. The goal is to make authentification

    $243 (Avg Bid)
    $243 Avg Bid
    11 bids

    "I need a firmware engineer for startin...Candidate must integrate low/level layers for accessing to basic hardware peripherals (ADC, UART, SPI...), as well as a library for FAT16/32 in uSD cards and FreeRTOS. Microcontroller being used is STM32F4. Ideally the candidate must have a STM32F429i Evaluation board and must be familiar with TrueStudio IDE."

    $216 (Avg Bid)
    $216 Avg Bid
    4 bids

    I have the program where the point in the code is traveling inside the 3d area. ...The program is running on custom assembled board with stm32f4 microcontroler, c programing language. I use Keil Uvison IDE. So idealy, you need to have board with stm microcontroller to run the code and debug. The code has around 500 lines in the problematic sketch.

    $41 (Avg Bid)
    $41 Avg Bid
    5 bids

    I need you to develop some software for me. I would like this software to be developed using C or C++. Embaded c for microcontroller CC3200

    $357 (Avg Bid)
    $357 Avg Bid
    10 bids
    electrical works Ended
    VERIFIED

    I'm working on a DIY project, I "m looking for someone to help me solder some power boards and microcontroller.

    $107 (Avg Bid)
    $107 Avg Bid
    19 bids

    need person who has knowledge about circuit design using latest opamps according our specifications after discussion only project will be granted pro...according our specifications after discussion only project will be granted project contains there parts [url removed, login to view] and HV part [url removed, login to view] eradication [url removed, login to view] section 4.microcontrol...

    $446 (Avg Bid)
    $446 Avg Bid
    24 bids

    I have a DTMF signal that arrives at 32-bit microchip microcontroller, I want to decode it and place it in a register inside the controller, later I will use this in the project that I am developing, I use tools MicroC to 32-bit microchip. Will be better speak spanish

    $173 (Avg Bid)
    $173 Avg Bid
    12 bids

    I need a temperature circuit diagram ( k type thermocouple amplifier) that is tested and proven to work on a very noise EMI and RFI, engine environment. Out...diagram ( k type thermocouple amplifier) that is tested and proven to work on a very noise EMI and RFI, engine environment. Output signals compatible with 5v atmega microcontroller "Arduino"

    $161 (Avg Bid)
    $161 Avg Bid
    22 bids

    We have an application for a microcontroller operating on 3.3V to read 0-10V analog output from sensors linearly proportional, i.e. 0V input will become 0V to be read by microcontroller and 10V becomes 3.3V. As we may receive voltage inputs up to 24V or more, we would like any values above 10V-24V to become 3.3V as well. This behavior is summarized

    $135 (Avg Bid)
    $135 Avg Bid
    22 bids

    Hey this assignment is due on 20th of october . its very hard for me to do it . we need to program the LCD of nokia 5110 we need to program the game using c++ the game given in the assignment sheet . that we can run it in the teensy . i need the code of the game. if i can get the assignmet as soon as possible it will be much better. please

    $205 (Avg Bid)
    $205 Avg Bid
    8 bids