...concentrators. The summary of what I'm looking for is: - Embedded code project written in C with following functional specs - SPI interface configured, nRF52(master) accelerometer(slave) - DMA configured for SPI reading of sensor data - sensor configured for 3-axis raw data, 12bit @10Hz - single ANT channel, configured for broadcast of most
...by a patient. It needs to record the time and send the information via bluetooth to the patients phone which has the app running over it. 2. The device is attached to the blister package and with the help of 3 sensors : Accelerometer, Contact Senor and a piezo sensor identifies if the medicine has been popped out or not. 3. This entire device is
...would be added onto the existing project you delivered. It is to have a hall Probe speed feedback that displays the speed in the ESP page. The other part is to use the Gyro accelerometer to be an impact detector. meaning If the vehicle goes over steady speed bumps the MPU6050 must give the rate of bumps in a value of say 0-300pulses/minute. This value must
I need to build a car dashboard with an Orange PI One. The da...horn. I have an Orange PI One, 5 inch HDMI Display (Rev 3.0) with touchscreen (XPT2046) , two touch sensors TTP223 (for turn signals) and an MPU6050 accelerometer , 3 axis gyro. The project is simple I need a car dashboard with a gauge, if is possible two one for rev and one for speed.
I need to build a ...horn. I have an Orange PI One, 5 inch HDMI Display (Rev 3.0) with touchscreen (XPT2046) , two touch sensors TTP223 (for turn signals) and an MPU6050 accelerometer , 3 axis gyro. The project is simple I need a car dashboard with a gauge, if is possible two one for rev and one for speed , in QT or something else, (prefered in QT).
...Controller Rev 3.0). This dashboard need to be put on a car which is running on compressed air. The dashboard needs to have a working speed gauge, to determine speed I have an accelerometer, a gauge to show how much air left in the tank, turn signals and honk. This is what I have : Orange PI One 5inch HDMI Display 800x480 Pixel XPT2046 Touch Controller Rev
...the PCB shape when you are hired. (18x) 3535 RGB NEOPIXELS Datasheet: (link removed) (4x) LED TACTILE BUTTONS Datasheet: (link removed) Drawing: (link removed) (1x) ACCELEROMETER ADXL362 Datasheet: (link removed) (1x) RIGADO BMD-350 Datasheet: (link removed) (1x) MICRO USB MID MOUNT SMT Product: (link removed) Datasheet: (link removed) (1x)
...following scope. Show an Airplane in the air then let user use Mobile Accelerometer to control up/down and left/right direction to land on a surface. Once it hits surface then finish the game. Graphic does not matter so you can select any graphics. It should work on iPhone and Android phone and Deadline to finish this test is 2 days. Thanks, Manisha
The scope of the project is to deliver an Android and iOS application (and source code) which performs the following operations: 1. Reads the ibeacons in the phone range 2. Read the phone accelerometer, gyroscope and compass 3. Packs all data into a message (format will be provided) 4. Send the data to AWS or local server using Internet (wifi or
I am looking for an adobe animate source file with a endless race car type game. The graphics are not important, I will be doing them later. I want the game to use the accelerometer to steer and accelerate. It should also have: -start page -a meter that refills every 24hrs and locks you out when its empty. one crash should use 1/4 of the meter - collisions
In the first phase: I want a camera triggered by accelerometer and powered by a battery. The picture can be very small and I need to send the picture wirelessly to either a hub or phone. Very simple prototype, can be off the shelf components e.g. raspberry pi, open mv cam, arduino preferably low power.
...want to realize and I was hoping you could help. I would need basically to make a one way transmitter, like a controller for a drone, but in this case i need to send gyro+accelerometer data to the pc via the wifi module. It needs to sit at the center of a Vinyl record turntable and send the speed of the RPMs to the computer. It all needs to fit into max
Create calculation of foot steps for my running apps using accelerometer
Create a basic running apps which have the (1)function of databases to let user login, (2) store location and calculated how many miles? (3) Menu activity (4) accelerometer
...layout as attached. Can change a bit. 2. BOM List for mass production. 3. Case Design for mass production. 4. 3D File 5. Firmware as follows. 6. Make 5 Prototypes. 7. A simple IOS apps to read the heart rate and contractions. Note the whole device must not be more than 5 cm by 5cm. Firmware Details for Contraction Tracker 1. Save all vibration
Hi, I wanted to develop an application for android or IOS mobile phone. The app has to be able to collect the user contexts and save them to a Database in background. The context are : 1- Location 2- Speed 3- Calendar 4- Time 5- Accelerometer I need this app be able to do two different tasks. The interface should has two different bottoms. 1-The
...postural pratictioner based in Italy. I found an android app that could be valuable for helping patients improve their posture; it is called Vibsensor and it logs data from the accelerometer onboard cell phones, creating analysis like fourier transform and average measures of angles. The problem is that the app is only available for phones, while I need a
...like this blog, [login to view URL] b. using some sensors like Accelerometer Magnetometer Gyroscope. But I think there might be several problems. For accelerometer and gyroscope. Integral will increase error during continuous operation? For magnetometer. Electromagnetic effect induced