My recent searches
Filter by:
Job State
1,484 antenna jobs found, pricing in USD

Assembling two different modules for dual sim phone: GSM and Sat-phone modules. Designing external sat antenna with connector. Writing script for maintaining sat module. Phone for sailormans, mountain climbers, areas without GSM broadcast.

$22 (Avg Bid)
$22 Avg Bid
5 bids

Expert in printed electronics and microwave antenna design with experience in 60 Ghz band.

$4736 (Avg Bid)
$4736 Avg Bid
8 bids
binaovi789 2 days left use it, for that there is no chance to doubt about uncomfortable. Active Technology: This device has great technology that give you useful advantages with Ceramic Chip Antenna with Bluetooth 4.0 and suitable for Android 4.3 or higher gadget and iOS 7 or Plus and its relative apps are available in the digital apps stores that easily combined with

$35 - $288
$35 - $288
0 bids

We need an RF engineer to help us design a PCB antenna. Tuned for 750-800MHz. Will need to be able to do fine tuning on samples we will fabricate.

$592 (Avg Bid)
$592 Avg Bid
27 bids

STAGE 1 Bootloader project especially hardware costs. includes: 1) Bread board board design/US...Purchase/assembly of 20 USB/RF module boards 4) Purchase of 20 enclosures including antennas 5) Courier/postage to Australia of 18 complete tested boards in enclosures with antenna. This milestone is payment for all the parts/labour/shipping of the above.

$385 (Avg Bid)
$385 Avg Bid
1 bids

...little inventory, without investing too much in the development of plastic moulds that will be expensive and maybe and will be requiring longer times for production. A solar antenna should be designed and placed that needs to be able to fold and saved again for installing the device outside buildings and in Outdoors for a better reception of Laser beam

$2490 (Avg Bid)
$2490 Avg Bid
16 bids

GPS ANTENNA UPGRADE PROJECT Overview The current design of the GPS Antenna is used on Tractors & other agricultural equipment. It runs on a C++ based program that parses the NMEA stream. This then outputs a square wave that represents speed to the Tractor. In certain models of our GPS antenna the raw NMEA stream data is also outputted. New project:

$1433 (Avg Bid)
$1433 Avg Bid
22 bids

...incorporate the entire code/algorithm F) Show me how to integrate the entire code into a ''DSP type'' G) All of it must go from a bluetooth antenna So maybe you could find an audio bluetooth antenna with an integrated dsp filtering ability Audio code if needed must be: 24bits on a sample rate of [url removed, login to view] And we will need some ba...

$597 (Avg Bid)
$597 Avg Bid
7 bids

...put it inside. The enclosure should be as low profile and compact as possible with an easy to manufacture and low cost design. Please read the manual for the LCD screen and antenna to see how they can fit and be attached. There is an example enclosure attached to the project for an idea. Must work within the constraints below. Enclosure Requirements

$182 (Avg Bid)
$182 Avg Bid
21 bids

...small router appliance for a very small scale production run for a client. The enclosure will house a single printed circuit board that is 160mm x 140mm and has openings for 2 antenna connectors, Ethernet and power ports, and leds. Deliverable will consist of files ready for 3D printing We are looking for a clean industrial look, with our logo on the top

$55965 (Avg Bid)
$55965 Avg Bid
21 bids

...the firmware part. We aim to target the following design infrastructure in order to achieve our targeted features : 1. PCB Design for single SoC i.e Nordic nRF52840 2. Antenna for long bluetooth range 3. Longetivity of coin cell 4. Built-in NFC tag for payments and NFC-A tag We would like to discuss more applications and target a future ready

$1672 (Avg Bid)
$1672 Avg Bid
20 bids

RPI HAT board Specs: 5V input pads for wire solde...outputs with MOSFET (4x) - max 10A with resetable fuse protection HUB75 connector on GPIO pins ([url removed, login to view]) GPS with connector for external antenna use RTC Accelerometer Industrial grade components Full schematics, board design files, BOM and gerbers

$308 (Avg Bid)
$308 Avg Bid
17 bids be an ekspert ind the following: - PCB design and production - BLE microcontroller - Inductive charging - Very very low power consumption - Temperature censor - Antenna design - Working with very small components - Getting the components fit our design. The present schematics is made ind Altium and we expect to keep the schematics in

$21 / hr (Avg Bid)
$21 / hr Avg Bid
26 bids
$159 Avg Bid
12 bids

Need an antenna design & its simulation on HFSS simulator. More details over the chat. ****Only bid if you have ever heard about this technology.

$104 (Avg Bid)
$104 Avg Bid
13 bids

details shared in the chat

$105 (Avg Bid)
$105 Avg Bid
2 bids

Hfss design of 64 (16x16)antenna array with coxail feed network on the middle on Fr4 substrate of 2.4 [url removed, login to view] must be simulated and proveded the work step by step.

$686 (Avg Bid)
$686 Avg Bid
8 bids

US Citizens only, able to pass security and background check, sign NDA. Design miniature horn fed parabolic TX antenna around DRA element print in 3D for testing.

$3904 (Avg Bid)
$3904 Avg Bid
7 bids

...candidates for 5G. In the context of indoor coverage, fiber wireless systems with multiple simplified remote antenna sites are attractive to avoid the indoor coverage problem caused by the high wall penetration loss of mm-wave signals. To allow enough antenna gain at the mm-wave bands, radio beam steering (and beam forming) is desired. Combining fiber-wireless

$411 (Avg Bid)
$411 Avg Bid
15 bids

Micro project review and complete i need to design an RFID module,using (rmd6300) chip and arduino to get the reader reading the tag using 125kHz antenna, include:source code,simulation design (proteus) and breadboard.

$59 (Avg Bid)
$59 Avg Bid
31 bids