|Wireless Arduino Light Switch
||I like to create an Arduino-based light switch that will turn on / off several lights in my room. Currently...standard North-American light switch with just an on/off position. I like to control the lights using both the...the standard light switch and the Arduino. I've done research and this can be done using a solid-state
||Wireless, Electronics, Microcontroller, Electrical Engineering
||Jan 25, 2010
||Jan 25, 2010Ended
|wirelessly controlled relay
||...open and normally closed
PCB 2 – (wireless control circuit)
• 230 volt AC input to screw terminals...to relay circuit (PCB 1) to switch relay
To recap, the wireless control circuit will constant keep relay...switched if power is supplied to PCB 2, this will switch the relay on PCB closing the normally open contact
||Electronics, Electrical Engineering, PCB Layout
||Mar 13, 2014
||Mar 13, 2014Ended
|Arduino UNO - RC Receiver Switch
||...PWM/PPM input from a Remote Control Receiver to code that will work on an Arduino UNO v2.
||Nov 20, 2013
||Nov 20, 2013Ended
|Thematic room - control with arduino
||...wiring scheme for next project:
Arduino Mega 2560
...posible to turn on/off with 4x4 code keypad or with a switch. More details will be described later.
||Sep 18, 2014
||Sep 18, 2014Ended
|For Hire: Arduino or Pi prototype 120volt switch
||...mouse trap in the switch world. I want to use an Arduino and a display to control a touch a standard
||Microcontroller, Electrical Engineering, Embedded Software, PCB Layout
||Aug 15, 2014
||Aug 15, 2014Ended
|Arduino software and controlling app
||Need an iphone app to control timing of 4 relays wirelessly. 6 different sequences. Using wifi bee connected
||Jul 24, 2015
||Jul 24, 2015Ends - 14h 9m
|Arduino Lights Control with Internet Requests.
||...and recieve information that will then control relays to switch lights on and off.
The system needs...240v with 10a.
The control process will work like this:
Each morning the arduino system will request...request an Internet address and receive light control information for that day. The information is requested
||Mar 11, 2012
||Mar 11, 2012Ended
||I need a control system written to control 3 relay's ,via push buttons one of them will be pulsed at...addition a single button power switch.
I have written a basic simple control system for 3 of the required
||C Programming, Engineering, C++ Programming
||Feb 1, 2015
||Feb 1, 2015Ended
|Play audio on arduino with smartphone app control
||...is to upload audio recordings (eg, mp3 files) wirelessly from a smartphone app to an electronics board...more details about the deliverables:
1. an arduino board with bluetooth connection and a little speaker
||Mobile Phone, iPhone, Cocoa, Arduino
||Jan 4, 2014
||Jan 4, 2014Ended
||...SainSmart Sixteen 16 Channel 12V Relay Module For Arduino ARM MSP430 TTL Logic BOARD (EBAY HAS THESE FOR...html
1 push start switch on
timer cycle starts 20 min on 3... relay6 turns on when momentary start/ stop switch is turned on (step1) but relay6 will open if
||PHP, Microcontroller, Arduino
||Mar 2, 2013
||Mar 2, 2013Ended
|Small Arduino project
||...connected to my Arduino ( mega) with the wires.
The tusk is:
1. to make this code work wirelessly using Nrf24L01...Nrf24L01 module. (from one Arduino to another. The best would be to use Arduino UNO)
2.I'd like to add...switches for slide axis and tilt axis.
(Each limit switch has to recognize the positive or negative end of
||Feb 19, 2015
||Feb 19, 2015Ended
||...allow an arduino to read a velocity signal from a pc usb port running driving simulators and control a servos...steering wheel.
The servo's or pots are required to control a separate high power circuit.
||Nov 16, 2013
||Nov 16, 2013Ended
||Arduino control of DC motor at 5-7 V DC
||Feb 27, 2015
||Feb 27, 2015Ended
|Arduino stepper motor control: Sketch and circuit
||...the corresponding position. On release of that switch, stepper motor will return to 0 degrees and power...down.
While any of the switches is closed, the Arduino also should close a 5-volt relay and keep it closed...seconds after the switch is opened.
Project will use the components I have: Arduino Duemilanove w/ATMega
||Electronics, Arduino, Circuit Design
||Jul 19, 2013
||Jul 19, 2013Ended
||...to hire someone to program an Arduino Uno or mega. It will need to control 5 motors and a heat wire.
I need this to be controlled by one up/down switch.
If this is something in your scope of work I
||May 23, 2015
||May 23, 2015Ended
||I have two Arduino Uno boards. I also have this wireless shield attached to each Arduino board:
http://www...to Arduino #1 as well as an LED to turn it on and off. I want to also control the LED on Arduino #2 via...via the proximity sensor attached to Arduino # 1.
Apparently it is plug and play, and I seemed to
||Mar 11, 2013
||Mar 11, 2013Ended
|Arduino sketch for Stepper Motor Serial Control
The scope of the project is to control a linear actuator that is powered by a stepper motor...motor, driven by a motor driver controlled via Arduino.
The consultant will be requested to analyse requirements...in use is a ST-M5045 2M542 and controlled via Arduino Uno and two limit switches are to be connected
||Electronics, Microcontroller, Arduino
||May 25, 2015
||May 25, 2015Ended
|Arduino stepper motor controller
||...Ardunio in order to control four stepper motors with switches and a selector switch.
[Removed by Freelancer
||Aug 21, 2012
||Aug 21, 2012Ended
|Timer for Arduino
||Project Timer for Arduino
Using a Arduino board (model to be specified) and LCD to control the trigger of...count down times
Input 1. From a user operated switch, normally open, starts timers counting down.
||Microcontroller, Embedded Software, Arduino
||Jun 5, 2014
||Jun 5, 2014Ended
|Arduino Web Integration
||...web page to an arduino device wirelessly to activate LEDs lights attached to the arduino.
Web page...available to the arduino device
- Receive instructions wirelessly to control activation...working integration confirming working web page and arduino device.
Please send me examples of similar work
||PHP, Microcontroller, Arduino
||Oct 21, 2013
||Oct 21, 2013Ended