|Arduino stepper motor control: Sketch and circuit
||I need a sketch and circuit to rotate a stepper motor to (and then hold at) any one of six positions...corresponding position. On release of that switch, stepper motor will return to 0 degrees and power down.
While...While any of the switches is closed, the Arduino also should close a 5-volt relay and keep it closed for an
||Electronics, Arduino, Circuit Design
||Jul 19, 2013
||Jul 19, 2013Ended
|Arduino DC PID motor Control Sketch
||Please see the attached documentation on the project.
||C Programming, Software Architecture, Arduino
||Oct 8, 2014
||Oct 8, 2014Ended
|Arduino sketch for Stepper Motor Serial Control
||...is powered by a stepper motor, driven by a motor driver controlled via Arduino.
The consultant will be...existing equipment. Design wiring schemas and a sketch as outlined in the description below
...degree, 24v, 4 wire stepper motor (LDO-42STH47-1684A). The Stepper Motor Driver in use is a ST-M5045
||Electronics, Microcontroller, Arduino
||May 25, 2015
|Arduino Sketch and Build Instructions
||...to write a sketch utilizing various arduino sheilds to complete a task. Using an Arduino Uno, Wave Shield...Shield, and Bluefruit EZ Link Sheild I would like a sketch written that would allow me to (via the bluefruit...sound clip while similtaniously triggering a servo motor to move 90 degrees from its set position and then
||Electronics, Microcontroller, Electrical Engineering, Arduino
||Aug 17, 2014
||Aug 17, 2014Ended
|Arduino sketch xbee integration
||...have a prototype of arduino based microcontroller code, as well as a fritzing sketch available. We are...getting the arduino to communicate via xbee with the existing sketch. We need the sketch working on our...The arduino devices have 3 sensors (with plans to add 2 additional at a minimum later) and 1 motor.
||Wireless, Electronics, Embedded Software, Anything Goes
||Aug 5, 2012
||Aug 5, 2012Ended
|Arduino sketch needed
||I need code written for Arduino project. Here are the hardware parts that I have that I need code written...written for:
Micro Controller: Arduino Uno / Arduino Pro Mini
Display: .96 I2C SPI 128x64.../ 1.8 TFT SPI 128x160
LED: 2 LED's
3 Way Navigation Switch (https://www
||Electronics, Microcontroller, Electrical Engineering, Embedded Software, Arduino
||Oct 29, 2014
||Oct 29, 2014Ended
|Simple Arduino sketch & circuit
||...TO ONE OF SIX POSITIONS:
Program Arduino to rotate a stepper motor to one of six fixed positions (60..."resting" position. I have a duemillanova and a motor control board, and the stepper. Need the program
||Feb 12, 2012
||Feb 12, 2012Ended
||Speed controller for elect motor
||Mar 1, 2015
||Mar 1, 2015Ended
|An Arduino sketch using 5" ITDB02 LCD board
||...you to write a simple arduino sketch like following :
I am using an arduino mega + a 5" ITDB02 LCD...LCD board + a stepper motor
1- you need to use the library at http://www.henningkarlsen.com/electronics/library...airspayce.com/mikem/arduino/AccelStepper/classAccelStepper.html , with an arduino mega 2560 R3 board
||C Programming, Microcontroller, Arduino
||Apr 10, 2014
||Apr 10, 2014Ended
|Write and test Arduino code for motor encoder.
||...the motors with the encoders, and create an arduino sketch (with associated libraries) that will:
-...(like a pressure switch)
I've been using a multi-motor driver shield with 2 x L293D chips (image attached)...problem.
I would like to express post you the motor driver shield and the 6 motors so you can test and
||Electronics, Microcontroller, Arduino
||Nov 25, 2014
||Nov 25, 2014Ended
||Hello, I have some open-source Processing Sketches that are not compiling. It appears to be due to a missing linear algebra library, but I have tried and retired to link it to me code with no luck. I'm looking for a solution to this, and likely an ongoing effort over the next week or so with more general questions.
||Jun 10, 2014
||Jun 10, 2014Ended
|C++ Job, I have a sketch for you to Adjust. Arduino RAMPS
*Four Motor control not more to do the following:
*No Duplex Circuit (yet).
** One motor moves one-Z...bed up.
** One motor moves one-Z bed down
** One motor moves X-Axis
** One motor moves Y-Axis
||C Programming, Engineering, Electronics, Microcontroller, C++ Programming
||Feb 23, 2015
||Feb 23, 2015Ended
||I have two Arduino Uno boards. I also have this wireless shield attached to each Arduino board:
http://www...to Arduino #1 as well as an LED to turn it on and off. I want to also control the LED on Arduino #2 via...via the proximity sensor attached to Arduino # 1.
Apparently it is plug and play, and I seemed to
||Mar 11, 2013
||Mar 11, 2013Ended
|Sketch for Arduino
I am trying to accomplish the following:
1. Arduino counts sequential button pushes
(Second push needs...the number of the LED pin
For an experienced arduino programmer this is probably less than an hour of
||May 30, 2014
||May 30, 2014Ended
||I would like to hire an Arduino software expert to work with me and teach me at the same time using Webex...the code if fully commented.
Arduino Uno with 1602 LCD/Keypad shield.
I will put this
||C Programming, Arduino
||Mar 29, 2013
||Mar 29, 2013Ended
|Small Robot Arm - Arduino(with StandardFirmata), Adafruit Motor Shield and FirmataVB (.NET)
||...the Adafruit Motor Shield (M1-M4) which sits on the Arduino - using FirmataVB. The arduino is running the...the StandardFirmata sketch that comes with the Arduino example sketches.
The 4 DC motors control arms...potentiometers. The potentiometers connect to the arduino via the motor shield analog ports and report to FirmataVB
||C Programming, .NET, Electronics, Microcontroller, Arduino
||Jan 18, 2013
||Jan 18, 2013Ended
|Arduino stepper motor controller
||I need a programmer to write the source code for an Ardunio in order to control four stepper motors with switches and a selector switch.
[Removed by Freelancer.com Admin]
||Aug 21, 2012
||Aug 21, 2012Ended
|Motor Script Arduino
||...code written to manipulate motor from an external source controlled by an arduino.
||Script Install, Software Architecture, Arduino
||May 8, 2014
||May 8, 2014Ended
|Arduino to Control DC Motor
||...code for Arduino the control DC Motor and i want to set my own speed of rotation of DC motor
||C Programming, , Arduino
||Aug 23, 2014
||Aug 23, 2014Ended
|Arduino dc motor control
Arduino dc motor control
The DC MOTOR turns forward and increases...increases the weight on the FORCE SENSOR.
The DC MOTOR turns reverse and decreases the weight on the FORCE...on the flex angle.
I an using:
Arduino with the motor controller.
||Dec 12, 2014
||Dec 12, 2014Ended