|Arduino stepper motor controller
||...programmer to write the source code for an Ardunio in order to control four stepper motors with switches and
||Aug 21, 2012
||Aug 21, 2012Ended
|Arduino Stepper Control
||...looking for a simple arduino sketch that will control the movement of a stepper motor on button press by...debounce code and the ability to add three momentary button switches.
Button 1 advances the stepper by...the stepper by a set number of steps (a variable to be input by me)
Button 3 advances the stepper while
||C Programming, Arduino
||Mar 11, 2013
||Mar 11, 2013Ended
|Arduino programmer needed for stepper motor code
||I need to add 3 stepper motors to an Arduino board and want to control them with potentiometers. I need...need to control the speed as well.
||Jun 18, 2015
||Jun 18, 2015Ended
|Arduino sketch for Stepper Motor Serial Control
||...project is to control a linear actuator that is powered by a stepper motor, driven by a motor driver controlled...controlled via Arduino.
The consultant will be requested to analyse requirements based on existing equipment...1.8 degree, 24v, 4 wire stepper motor (LDO-42STH47-1684A). The Stepper Motor Driver in use is a ST-M5045
||Electronics, Microcontroller, Arduino
||May 25, 2015
||May 25, 2015Ended
|Stepper motor control board with Arduino
||...design for a control board for testing a motorized lens debugged. I can't get my stepper motor drivers to...to work correctly.
The board has 3 stepper motor drivers (https://www.pololu.com/product/2134) that...an Arduino (https://www.sparkfun.com/products/12757) or a separate 555 timer and use the Arduino to enable/disable
||Electronics, Electrical Engineering, Arduino
||Jul 10, 2015
||Jul 10, 2015Ended
|Arduino/Adafruit stepper control
||...written for a Arduino and a Adafruit v2.0 motor shield controlling a Adafruit Stepper motor.
v2.0 Motor shield
The program would work as follows:
Push button...button (a first time)
LED turns off and the motor turns clockwise 50 steps and stops (release) and then the
||Oct 19, 2013
||Oct 19, 2013Ended
|Stepper Motor Control
||This code will perform Rotation of STEPPER motor in clock wise and anticlockwise direction.
||Engineering, Embedded Software
||Dec 1, 2013
||Dec 1, 2013Ended
|Servo/ Stepper motor control
||...should be very accurate so I guess we must use stepper, but if you have any other idea - please let me...program(s) in executable form as well as complete source code of all work done.
2) Deliverables must be in...Platform
It should be easy to control the parameters described.
||Engineering, Electronics, Anything Goes
||Apr 5, 2009
||Apr 5, 2009Ended
|Stepper Motor Speed Regulator with arduino
||This project need to be done with Arduino using Touch screen like an interface.
You need to do the programing...direct control of 2 phase Nema 17 stepper motor with this Specifications
Voltage (stepper motor): 5-12VDC
...torque need to be on max at any speed.
Control range of stepping motor speed: 0~100 rpm (adjustment in 0,1
||Electronics, Microcontroller, Electrical Engineering, PCB Layout
||Jul 6, 2014
||Jul 6, 2014Ended
|Arduino stepper motor control: Sketch and circuit
||I need a sketch and circuit to rotate a stepper motor to (and then hold at) any one of six positions...the stepper will rotate to and hold the corresponding position. On release of that switch, stepper motor...down.
While any of the switches is closed, the Arduino also should close a 5-volt relay and keep it closed
||Electronics, Arduino, Circuit Design
||Jul 19, 2013
||Jul 19, 2013Ended
||I need to control a stepper motor using atmega16
i need the c code and the simulation file using proteus
||Apr 13, 2013
||Apr 13, 2013Ended
|Connect 4 game using Arduino to run stepper motor
||...4 game. There are 2 stepper motor which need to be control through Arduino code. The software should
||PHP, Software Architecture
||Apr 2, 2015
||Apr 2, 2015Ended
||May 30, 2013
||May 30, 2013Ended
|XY Stage with Stepper Motor Control
||...uses two stepper motors to move a very small carriage in 3x3 inch 2D space. We need to control the system...particularly in;
-Selection of stepper motors,
-Selection of associated control hardware,
-Putting together...together a demonstration "software code" working in C++ environment that a) initializes the system, b) tracks
||C Programming, Electronics, Microcontroller, Electrical Engineering, Robotics
||Sep 13, 2013
||Sep 13, 2013Ended
|Stepper Motor controlled through Arduino board by joystick
||...simple application that can control 2 steppers with a joystick using an Arduino board . I attach photos of
||C Programming, Arduino
||Apr 25, 2013
||Apr 25, 2013Ended
|Arduino programmer needed for stepper motor setup
||...need to add a couple of stepper motors to an Arduino board and want to control them with potentiometers...potentiometers. I need to control the speed and direction as well.
||Jun 29, 2015
||Jun 29, 2015Ended
|multiple stepper motor control with arduino mega + ramps1.4 + a4988 drivers
||right now i can only run one motor at one time.
the target is that control 3 motors independently at...input is pressbutton. the program is store in arduino and witiout PC when the system is operating
||PHP, Software Architecture
||Apr 16, 2015
||Apr 16, 2015Ended
|Stepper motor program
||...use program for controlling X, Y, Z motion of stepper motors from a basic Windows PC environment.
##...use program for controlling X, Y, Z motion of stepper motors from a basic Windows PC environment. It...to process DXF type CAD files into G code commands. The G code commands can be plotted on screen at any
||PHP, C Programming, Visual Basic, Windows Desktop, Delphi, Engineering, CAD/CAM, Software Architecture, Software Testing, Microsoft, MySQL, 3D Modelling
||Nov 17, 2003
||Nov 17, 2003Ended
|Arduino to Control DC Motor
||...want C code for Arduino the control DC Motor and i want to set my own speed of rotation of DC motor
||C Programming, , Arduino
||Aug 23, 2014
||Aug 23, 2014Ended
|Arduino Stepper control with I/O logic
||...an Arduino UNO or Leonardo develop a program to do the following:
On power up drive a stepper motor...an analog voltage signal to an input.
Stop the motor and advance 1 step in opposite direction. Set this...source, needs to be an interrupt, move the stepper motor a set amount of steps AWAY from home position
||Electronics, Microcontroller, C++ Programming, Arduino
||Oct 23, 2013
||Oct 23, 2013Ended