Arduino xbee logger jobs

Filter

My recent searches
Filter by:
Budget
to
to
to
Skills
Languages
    Job State
    9,951 arduino xbee logger jobs found, pricing in USD

    Project on multi-robot communication and coordination by building a mesh network (xbee / Bluetooth etc ) .

    $39 (Avg Bid)
    $39 Avg Bid
    1 bids
    Product Design Consultancy 6 days left
    VERIFIED

    Consultancy on : 3D SLS printed arduino controlled integrated motor (magnets are in the bit that moves) based product avoiding traditional esc for motor etc & to increase efficiency Product Design.

    $24 (Avg Bid)
    $24 Avg Bid
    3 bids

    we need barcoding solution designed on Respberry Pi and Arduino devices or other. A weighing scale will be connected to measure the weigh of box and print the barcode with weight and material info. also need dispatch systems accordingly. client server based system, stock management, production, dispatch stock date wise reports and should be easy to

    $846 (Avg Bid)
    $846 Avg Bid
    3 bids

    I would like someone to create me a joystick which controls two stepper motors, rotating one when the joystick is moved in the x direction and rotating ...controls two stepper motors, rotating one when the joystick is moved in the x direction and rotating the other if i move in the y direction. The joystick must be coded with arduino, preferabbly UNO.

    $686 (Avg Bid)
    $686 Avg Bid
    4 bids

    I am looking for arduino programmer who live Malaysia

    $503 (Avg Bid)
    $503 Avg Bid
    5 bids
    Arduino Code 6 days left

    Need to develop the arduino code for the Obstruct avoidance with the PID controller

    $108 (Avg Bid)
    $108 Avg Bid
    20 bids

    Arduino coder required. Development of small sketch to obtain i2c serial data stream from Blackmagic Camera Control Arduino shield (full API/libraries are available for the shield) and output this stream via both serial (RS-232) and ethernet (UDP stream) simultaneously. Corresponding sketch to be developed to receive the RS-232 and UDP streams and output

    $153 (Avg Bid)
    $153 Avg Bid
    11 bids

    adafruit flora or gemma project

    $619 (Avg Bid)
    $619 Avg Bid
    22 bids

    I'm looking for a freelancer (or a team) who is located in China. I need an electronic engineer skilled in Arduino, Raspberry Pi, WiFi, Bluetooth, PIC, PLC and professional in Electronics schematics and PCB design (Altium)–Circuit analyzing and debugging- Hardware reverse engineering - Firmware development –C++, C- microcontroller embedded system -

    $755 (Avg Bid)
    $755 Avg Bid
    14 bids

    ESP32 function library for Arduino environment: setup the library to search for BLE AND BT ( paired ) devices, returning the MAC with the RSSI in a loop. FOR BT setup the pairing as well Input: 1-n - number of device found - typ ( BLE/BT) - MAC adresse or some unique identifier - name

    PHP
    $640 (Avg Bid)
    $640 Avg Bid
    10 bids

    He construido una cortacesped eléctrica automática con un arduino basándome en un proyecto existente en internet. Actualmente la función de la cortacésped es cortar en linea recta, en caso de coche contra pared real o valla digital gira aleatoriamente y sigue cortando en linea recta. me gustaría realizar un cambio en el código para que ...

    $166 (Avg Bid)
    $166 Avg Bid
    4 bids

    I need someone who can create arduino program using the existing RAMPS v1.4 boards that is being used for 3D printing (XYZ,EXT0,EXT2) ports with DRV8825 stepper driver to run multiple servo motors in one direction with specified steps at a time ... example: when z limit switch is ON run all Z axis motors (N steps or N Revolution) when y limit

    $146 (Avg Bid)
    $146 Avg Bid
    12 bids

    Use CAN bus interface to collect data from vehicle. Development and Software implementation of a Data Management algorithm to reduce the amount of CAN receive data. It should filter the signals within CAN message with respect to the signal values. Store the filtered CAN data on the SD card. Upload the data file from SD card to the server. The hardware is STM32 Nucleo-64 development board w...

    $733 (Avg Bid)
    $733 Avg Bid
    8 bids

    ...Requirements: Must be experienced with Kicad. Must be knowledgeable about power electronics. Experienced designing gate drive circuitry. Experienced writing C code in arduino Timeline: First revision of schematic within 5 days Second revision of schematic within 4 days Subsequent minor schematic changes in 1 day PCB layout under 2days Software

    $190 (Avg Bid)
    $190 Avg Bid
    9 bids

    Initially I am using an arduino uno to control two bipolar stepper motors and two relays. Following an initial command to Alexa - "Alexa please demonstrate the action" The 1st stepper motor rotates through 200mm of movement, then 2nd stepper does the same, then relay 1&2 are actuated, The system will then run for 8 hours or until Alexa is told to return

    $100 (Avg Bid)
    $100 Avg Bid
    1 bids
    Tecnico Electronico 4 days left
    VERIFIED

    ...prototipos, disponibilidad de al menos 2 horas diarias, se valoran los siguientes conocimientos: - Soldadura smd - Diseño de circuitos - Bajo consumo - GPS / RF - Arduino - Microcontroladores / rTos ...

    $7 / hr (Avg Bid)
    $7 / hr Avg Bid
    12 bids

    Hi I am looking for someone to be able to make or use a amazon alexa echo command where i can say “Alexa, Turn Motor On” I have a Amazon Echo Arduino Raspberry Pi with stepper motor I need you to be able to set up a demo for me so i can use the command and the motor will function User must answer 6+3 = ? to avoid spam Thanks

    $225 (Avg Bid)
    $225 Avg Bid
    20 bids

    Arduino based PLC programmer. Looking for an arduino based PLC programmer . This is a transition from another PLC. No development required. Only SW coding to the new Arduino based PLC platform. Old code available in VB. PLC will monitor and control various live sensors. ( 50 sensors) . NDA will be required before start. Estimated work in total

    $1193 (Avg Bid)
    $1193 Avg Bid
    28 bids

    Require coding and circuit design based on truth table and discussion

    $421 (Avg Bid)
    $421 Avg Bid
    9 bids

    ...files and 5 prototypes of a PCB with headers for a Particle Electron, Arduino Nano and an XBee. Along with that, we require a thermistor in series with a 10k resistor to use as a temperature sensor, and two voltage regulators (9v and 5v) that can reliably power an Arduino Nano, XBee and a 10ma sensor. I've included an Excel document to sketch out

    $449 (Avg Bid)
    $449 Avg Bid
    13 bids