Beagle board pcb jobs

Filter

My recent searches
Filter by:
Budget
to
to
to
Skills
Languages
Job State
16,213 beagle board pcb jobs found, pricing in USD

Smd pcb development. modifying the current PCB design with Op amps resistors and other modules.

$293 (Avg Bid)
$293 Avg Bid
17 bids

Need a custom control board designed to control a main led light source, a secondary led light source that activities with impact, power switch, and speaker. The board needs to be able to play the sound files based on the movement of the device. No more than 0.8" wide board. The board and speaker need to fit inside a.0.9" wide cylinder.

$157 (Avg Bid)
$157 Avg Bid
11 bids

I need a pcb board for a wifi device that interacts with my website.

$182 (Avg Bid)
$182 Avg Bid
24 bids

I have 2 JPG images, one of the top of a small circuit board and another of the bottom of the same one. I was wondering if someone could create Gerber files out of these so the pcb can be manufactured, thanks The files are attached bellow.

$28 (Avg Bid)
$28 Avg Bid
13 bids

Design a TR21 flex PCB and output Gerber files and 3D PDF.

$159 (Avg Bid)
$159 Avg Bid
10 bids
Flex PCB design 5 days left

Design a TR20 flex PCB and output Gerber files and 3D PDF.

$168 (Avg Bid)
$168 Avg Bid
13 bids

We would like to hire someone to design (no PCB needed, only schematic but the simulation needs to be as accurate as possible) a crystal notch at a specific frequency (in the MHz). We already have the quartz, we also have every parameters of each piece (Fs, Fp, Cs, Cp, Q, Rs ...) This filter needs to be matched at 50ohm IN and OUT. Attenuation

$185 (Avg Bid)
$185 Avg Bid
12 bids
PCB design 5 days left

I need a relatively simple PCB designing for a short POC run. The design is a 200 pin SO-DIMM socket with each pin tracked out to a pad large enough to solder by hand. It needs to be as small as possible while remaining usable.

$80 (Avg Bid)
$80 Avg Bid
4 bids

...experienced EU based PCB designer for the following "mSATA to USB 3.1 Type-C Adaptor (mass storage USB 3.1)" This is custom designed mSATA (SSD) to (Mass Storage) USB 3.1 (Type-C) adaptor. - Design based on ASMedia USB bridge are preferred - Design based on Texas Instruments USB bridge is the second preference - Maximum 4 layer ([url removed, login to view]) PCB i...

$943 (Avg Bid)
Urgent NDA
$943 Avg Bid
6 bids

I need a simple 8 circuit common bus pcb designed. Each of the 8 common busses should have 18 holes that can accommodate 18AWG stranded wire. I'd also like there to be a test point for each of the 8 busses. The test points will need to be multimeter probe friendly so that a technician can plug one of the multimeter's probes in one test point and

$24 (Avg Bid)
$24 Avg Bid
29 bids

I am looking for an electronic engineer to design a circuit and making PCB for manufacture

$130 (Avg Bid)
$130 Avg Bid
19 bids

Im looking for a developer based in South Africa (must be based in SA) to develop a job site/job board - similar to careers24. I do not know what skills are required.

$728 (Avg Bid)
$728 Avg Bid
41 bids

Hi, I have 3 PCB files that need modification in PADS. Changes have already been made in Altium for same PCB files, but i want same changes to be done in PADS.

$140 (Avg Bid)
$140 Avg Bid
19 bids

I would like to make a modular phone charger. If you have experience with PCB design and electronics feel free to respond! Please see attachment for requirements.

$222 (Avg Bid)
$222 Avg Bid
36 bids

Make a simple adapter board to split one power input into several high power lines.

$42 (Avg Bid)
$42 Avg Bid
7 bids

Hello, We have custom hardware running on properly on kernel [url removed, login to view], this kernel is modified with vendor patches to support the custom hardware. The processor is a PXA270 520MHz processor. However to run some software it doesn't match the minimal kernel version. We fetched kernel 2.6.29.6 and applied the patches for [url removed, login to view] (last supported ...

$18 / hr (Avg Bid)
$18 / hr Avg Bid
7 bids

...the board should be in approximately a 2:1 ratio and can be any size smaller than 154/77mm. The board should be as thin as possible All of the ports should be along the edge of the board and facing parallel to the pcb even including the pcie x16. Only the Sodimm and m.2 connectors should not. The camera should be on the back side of the pcb facing

$200 (Avg Bid)
Guaranteed
$200 Avg Bid
2 entries

Hi, I have a project that needs to be done in Altium designer. I will provide the schematic and BOM. You need t...will provide the schematic and BOM. You need to create the footprint library and layout and generate gerber once design is approved. I need design in 3 days (it's 4 layers board). If you have Altium designer experience, please let me know.

$162 (Avg Bid)
$162 Avg Bid
39 bids