Purpose of the project is to connect to a web-radio, receive the audio streaming and play it. System specs: - We will use the STM32Discovery STM32F407 + STM32F4DIS-BB, to evaluate the solution - Use STM32CubeMX to generate the initial framework sw Sw specs: - Create a web page where is possible... - Select, from a list, one web radio - Select to plays the audio streaming (using the onboard h...
I need firmware programmed for a STM32F4 Discovery board that reads the on-board microphone, performs FFT on those samples, converts magnitude to dbFS and then sends the data in freq, magnitude format over USB. Sample rate should be as high as possible 44.1Khz, 48Khz. The program should also turn on one of the GPIOs if a certain message is received
...product development on a team where nobody has specific experience interfacing an STM32F using the FSMC option. In short, our product has a networking subsystem running on a STM32F4. I want to ensure that we have a fast interface with our an AllWinner A64 motherboard. Here is a link to this motherboard: [login to view URL] The SOPINE
I need programmer to help me finish up an application for a STM32F4 Discovery. The application must read samples from the onboard MEMS microphone and run FFT. It will then report the frequency,magnitude values over USB. The existing code has USB running as custom HID and the actual microphone sample acquisition and transmission must be implemented
...project eventually include Device Firmware Upgrade via USB as seen in application note : STSW-STM32080 Prior to this implementing DFU via USB, we want to create firmware that can output data from a structure in C based on a timer or other synchronization over the USB Bus. We will need either a Linux (perferred) or Windows utility to save this data in
We have a need for a Quick Turnaround on this project an experienced Embedded programmer for a STM32F4 project involving simple register requests over I2C , full annotated code and test bin files will be required, the device that the MCU needs to communicate is an STUSB4710 [login to view URL]
We have built an embedded board for a specific application, with these characteristics: - STM32F4 (STM32CubeMX libraries 4.21) - raw LWIP - No OS - Multidrive for micro SD and USB host, using FATFS We had implemented a web server, TCP/IP commands, files upload via a web page. We want to have an FTP server.
i am looking for firmware programmer who has good experience with stm32f4 discovery kit development i want to use DAC module with DMA interface for more details inbox me
The idea of this project is to generate signals(messages) with TIM3 using capture/compare mode and display data on LCD TFT and on PC terminal using USART1. Before everybody bids please see attached file.
We have a large amount of existing software which controls a series of green waste composting systems. It currently runs on an STM32F4 processor, and displays data on a 4 x 20 LCD. It is written in C on Mikroelectronica Mikroc ARM compiler, V 6.0.0. We wish to upgrade to an STM32F746G with LCD as below. We need a graphics library and commented
I'm looking for someone to code a cross platform DFU uploader for an attached STM32F4 chip. Written in Java is fine, to create code re-use. Want app to list available DFU devices and allow selection of a file to upload.
IR Infrared Flame Sensor and Rain Drop Sensor stm32f4
"I need a firmware engineer for starting with the proof of conce...low/level layers for accessing to basic hardware peripherals (ADC, UART, SPI...), as well as a library for FAT16/32 in uSD cards and FreeRTOS. Microcontroller being used is STM32F4. Ideally the candidate must have a STM32F429i Evaluation board and must be familiar with TrueStudio IDE."
...and give me repair solution. Maybe, some other variables are not correctly defined or maybe here is a memory leak. The program is running on custom assembled board with stm32f4 microcontroler, c programing language. I use Keil Uvison IDE. So idealy, you need to have board with stm microcontroller to run the code and debug. The code has around 500
Hi tifoda, I saw you recently completed a project for "Jammel0500" about a remote temperature sensor on the STM32F4. I am trying to get something similar working in C++ (for personal use, not commercial/school work) but can't figure out how to take an ADC reading from the internal temperature sensor. Would you consider providing me with the relevent
Hi JinDongZhe, I was recommended from a friend who did work from you. And I want you to help me as the work you did for him before is nearly s...work from you. And I want you to help me as the work you did for him before is nearly similar to the one I want right now, maybe a bit easier. It's about software C++ using STM32F4 board. Let me know please.
Propose IoT architecture for existing Industrial product. Product is based on STM32F4 Family micro-controller with 1MB Flash and 512KB RAM and USB OTG capability. I prefer to interface WiFi dongle to USB OTG for cloud connectivity. You need to prepare detailed architecture document. You need to make make recommendations for USB stack, cloud, protocol
...noticed you had KWP2000 and UDS listed in your skills. I'm looking for someone to write a library that can be used for ISO 15765-2 (iso-tp). This library would need to send and receive. It will be used on an embedded platform (going to use STM32F4 I think). I am not a company, just an enthusiast. Look forward to your response. I am open to discussion
I am looking for a freelancer to help me with my small project. The skill required is Microcontroller STM32F4.
SMT32F429IET, USB Host (MSC) USB Disk file write/read on FREERTOS (other codes ready with TouchGFX GUI)
...the algorithm which is available as a flowchart. Programming and final result should be done using Keil ARM uVision ver 5 as a programming software as a ARM project for STM32F4 Discovery and also version for STM32F1xx. Programming should be done for ARM Cortex-M4 STM chips STM32407 and also version of code for STM32F1xx . This code also, should
I have a STM32F4 discovery board and need to send data to [login to view URL] or [login to view URL] or any other similar site using GPRS and WiFi. You need to write a sample program for sending data when switch is pressed to some site like [login to view URL]
I would like to develop micro grid tied inverter based on discovery board STM32F4 for testing control algorithm.
...constant voltage, with configurable amplitude. A sine wave, with configurable amplitude and frequency. A square wave, with configurable amplitude and frequency. i am using STM32F4 micro- controller . Using MBED compiler . i am looking for someone who is really good at programming and he has some skills like c++ ...
Keil μVision using the HAL drivers for the STM32F4 dicovery board hardware
...memory buffer. Another function to take the memory buffer and store it to the eeprom. We can pass in the CRC and size to ensure there is no corruption, if the file fails we simply return false. This will be for the stm32f4 microcontroller and should work on the stm32f4 discovery board. something like this Structure update update len update crc void