Comsol programming matlab jobs

Filter

My recent searches
Filter by:
Budget
to
to
to
Skills
Languages
    Job State
    281 comsol programming matlab jobs found, pricing in USD

    I need an topology optimization of a simple magnetic circuit (closed shape yoke, one coil, 3D).

    $138 (Avg Bid)
    $138 Avg Bid
    4 bids

    Need someone that is expert in using COMSOL software and know how to design a battery and use the electrochemical function in it.

    $22 (Avg Bid)
    $22 Avg Bid
    1 bids

    Hello sir, I need help with COMSOL to stimulate wear on a Pin on disk experiment, but here between two contact pair bodies one will be fixed and other will be making oscillating motion with a frequency of 20Hz, length of cycle is 2mm(1mm tro and 1mm fro) and it runs for 10min, a force of 10N will be applied and wear coefficient will be 2.7E-10. I need

    $40 (Avg Bid)
    $40 Avg Bid
    3 bids

    ...is a transient heat distribution from the thermal camera as in the picture below.. I have already modeled the same although in stationary(time independent distribution) in comsol. The temperature distribution is almost similar, however an unrealistic temperature is being observed in the model. I have considered a natural convection above and below the

    $31 (Avg Bid)
    $31 Avg Bid
    5 bids

    The idea is to have ...needs to be modelled in comsol. I have to do the same for 3 types of meanders, but i need help for one as I would like to learn too. So a temperature distribution of the below meander (one from the second row in the jpg attached)with a an explanation of steps used to model this would be great as I have no experience in comsol

    $22 (Avg Bid)
    $22 Avg Bid
    3 bids

    I need support and advise to improve a 3D model with comsol (AC/DC module). If you have experience building 3D models please contact me, I can provide you with more information about the project. Proven experience with a similar project in the past will be highly valued. Thanks

    $44 (Avg Bid)
    $44 Avg Bid
    16 bids

    I am looking for a freelancer with experience using COMSOL Multiphysics to complete a 3D electrostatic model, in order to define the potential and electric field distribution between two solid dielectrics. Thanks

    $182 (Avg Bid)
    $182 Avg Bid
    11 bids

    Simulations FEM on the performance of PZT and PVDF

    $32 (Avg Bid)
    $32 Avg Bid
    4 bids

    I'd like to design a biosensor by using comsol

    $300 (Avg Bid)
    $300 Avg Bid
    4 bids

    I'm looking for an electrical engineer who is experienced in low frequency simulation using either COMSOL Multiphysics (AC/DC module) or CST (EM Studio). The job is to provide advice and support as required on the setup of a new model. It involves calculating the response of an inductive pickup coil sensor to an external magnetic field. Experience

    $16 / hr (Avg Bid)
    $16 / hr Avg Bid
    4 bids

    I'm looking for a freelancer capable to improve two 3D models using COMSOL, to define the potential and electric field distribution between two solids. The challenge of this project is to mesh microns size geometries of several defects that have to placed between the two solids. You will also need to describe the results of the 3D models, plot line

    $164 (Avg Bid)
    $164 Avg Bid
    23 bids

    I have developed two 3D models in comsol 5.2, which contains micron-size components to study the potential and the electrical field distribution within solid dielectrics. I need help to improve the geometry of the two models and their mesh. I also need help finding areas of the potential and electrical field enhancement, when the defects are introduced

    $187 (Avg Bid)
    $187 Avg Bid
    15 bids

    ...that the actual 3D model can absorb. - Provide graphs as a proof of working system, as well as animation. If Phase A is successful, another job will be post for: Phase B (COMSOL only as I doubt that this can be done in Solidworks): - Build a schematic simplified 2D model to used as a based to build an abacus graph - Run iterative simulation with

    $150 (Avg Bid)
    $150 Avg Bid
    3 bids

    ...that the actual 3D model can absorb. - Provide graphs as a proof of working system, as well as animation. If Phase A is successful, another job will be post for: Phase B (COMSOL only as I doubt that this can be done in Solidworks): - Build a schematic simplified 2D model to used as a based to build an abacus graph - Run iterative simulation with

    $65 (Avg Bid)
    $65 Avg Bid
    12 bids

    ...wall temperature distribution, and the air flow in a drying setup using a 2D or 3D COMSOL model (v.5.3) for a convective air flow. The model is very simple: the cold moist air sucked into the setup, heated up by a heat source, and let out through the [url removed, login to view] COMSOL file is available, but there are some wrong set boundary conditions. No need to model

    $190 (Avg Bid)
    $190 Avg Bid
    7 bids

    Need to simulate the wall temperature distribution, and the air flow in a drying setup using a 2D or 3D COMSOL model (v.5.3) for a convective air flow. The STL or DXF files of the setup are available. No need to model the drying of material: only the air flow and temperature distributions. The moist air is let in into the setup, heated up by a heat

    $100 (Avg Bid)
    $100 Avg Bid
    2 bids

    Small cfd simulation with FSI involved. Software: LS-Dyna or Comsol

    $60 (Avg Bid)
    $60 Avg Bid
    8 bids

    Small cfd simulation with FSI involved. Software: LS-Dyna or Comsol

    $227 (Avg Bid)
    $227 Avg Bid
    1 bids

    HT and fluid flow analysis for flow through microchannels

    $121 (Avg Bid)
    $121 Avg Bid
    10 bids