Freelancer pcb job jobs

Filter

My recent searches
Filter by:
Budget
to
to
to
Skills
Languages
    Job State
    8,932 freelancer pcb job jobs found, pricing in USD
    Power Supply Design 6 days left
    VERIFIED

    *Please read this very carefully and only apply if you feel competent to do all the tasks in a timely fashion* I have a very small PCB (40*30mm) design which has been made up ,I need someone outside of the project to evaluate [url removed, login to view] design is not complicated but will need someone who is very familiar with power supply design. They must be : *A

    $122 (Avg Bid)
    $122 Avg Bid
    9 bids

    A small form factor PCB with simple components

    $113 (Avg Bid)
    $113 Avg Bid
    19 bids

    Firmware Design of STM32 ARM Cortex Sensor PCB in C Compiled with GCC Project Objectives: – Understand elements of a small PCB design, sensor data and signals – Consultant to write and test firmware for said PCB. Fully documented code required. Target Price for Project: US$750 or less Expertise Required: – C – GCC – Signal Processi...

    $1093 (Avg Bid)
    $1093 Avg Bid
    14 bids

    we have several PCB boards which were detected as a source of 100MHz emission in the lab. We would like to find the source of this signal with our spectrum analyzer(Siglent SSA3032X). we have probes and did some tests already, but it's hard to find anything useful since it's a new experience for us and we do not even know where to look. We need someone

    $47 / hr (Avg Bid)
    $47 / hr Avg Bid
    7 bids

    programming the code for the esp pcb board till 4.10.17. functions as discussed by messenger.

    $2760 (Avg Bid)
    Full Time
    $2760 Avg Bid
    5 bids

    ...light. Here are the deliveries for each circuit: * Kicad files for the schematic and a PCB (no need to route wires on PCB since I will be modifying design to fit into a bigger project) * A prototype of the circuit proving its operation (can either use the PCB or be hand soldered on a protoboard) Payment Schedule: * One-third of payment delivered

    $519 (Avg Bid)
    $519 Avg Bid
    20 bids
    Electronic Timer Design 6 days left
    VERIFIED

    NDA required. The device will be 8" Long x 2" Deep x 2" Height It is a timer actuated by the re...bar. Each of the four timers can be adjusted independently. Low battery indicator light required. Power on/off required. Need the electronics for above device including PCB, schematic, LED, battery, etc. Need the enclosure design and all mechanical

    $254 (Avg Bid)
    $254 Avg Bid
    17 bids
    PCB Design Engineer 6 days left
    VERIFIED

    PCB DESIGN USING MENTOR GRAPHICS DXDESIGNER & PADS LAYOUT ,ROUTER & LOGIC.

    $2558 (Avg Bid)
    $2558 Avg Bid
    9 bids

    Cuento con un esquema eléctrico y pcb funcionando, con varios módulos (fuente regulada, arduino, rtc, sim800, etc). Necesito revisión y mejora del diseño pero además necesito asesoramiento relacionado con mejorar la confiabilidad y autorecupero en caso de fallo o cuelgue de alguno de los módulos del circuito.

    $202 (Avg Bid)
    $202 Avg Bid
    8 bids

    I make a custom PCB and develop the code I want someone can write the correct code and maintain the automation with Blynk. I can give the remote access to make tests and the code. My pcb have atmega328p, sim800l, 3 servo motors, temperature sensor, ph meter, a clock, and 2 floats. I want finish this project in 48 hours.

    $134 (Avg Bid)
    $134 Avg Bid
    7 bids

    I am looking to design a PCB controller for a current project. I will need the following done: - Refine controller logic - Component Selection - Firmware programming - produce an arduino based working prototype

    $333 (Avg Bid)
    $333 Avg Bid
    40 bids

    I have a custom PCB, and fully compatible with arduino library. I want a custom module with MQTT protocol to enable access with arduino. It's urgent! Thank you for everybody!

    $33 (Avg Bid)
    $33 Avg Bid
    6 bids

    optimize or redesign the manufacturing process for producing a 10layer pcb

    $171 (Avg Bid)
    $171 Avg Bid
    11 bids

    Hi Hiren A., I have a PCB development project for an LED lighting product I would like to discuss with you. The $50 budget offer is NOT the planned budget, this was just to open up the chat. We can set up the actual cost and milestones once we chat and decide to move forward with this project.

    $50 (Avg Bid)
    $50 Avg Bid
    1 bids

    design and recommend best process for developing a pcb based on the attributes of the gerber files of the subject board

    $180 (Avg Bid)
    $180 Avg Bid
    26 bids

    ... OpAmp IC, caps, transistors etc.) and breadboard test for proof of concept. 2) It would be good if I could have the recommendation design/information required to have a PCB manufactured. 3) A recommendation for good simulation software that I can observe the circuit working etc. (e.g. LTspice) 4) Testing / sample code (if possible) of it working

    $419 (Avg Bid)
    $419 Avg Bid
    17 bids

    pm for more details

    $67 (Avg Bid)
    $67 Avg Bid
    12 bids

    NDA required before work begins. Need a DC motor to move a 5 pound object up and down over a distance of 20 feet upto 100feet. Need DC motor spec Need PCB prototype and schematic, inclduing resistors, transformers, etc. DC motor will move object by the most cost effective method (rail, wire rope, belt) Plug into AC wall outlet which will drive

    $252 (Avg Bid)
    $252 Avg Bid
    16 bids

    Replace text in Adobe Illustrator file. Deliver normal and text outlined file. Quality = Qualität PCB Design = PCB Design PCB Fabrication = PCB Produktion PCB Assembly = PCB Montage PCB Repair and Rework = PCB Reparatur und Rework Cable and Wiring Techniques = Kabel- und Kabelbaumtechniken Special Training Programs = Spezielle S...

    $22 (Avg Bid)
    $22 Avg Bid
    13 bids

    This involves taking existing components (pcb), removing them from their housing, and conjoining them into a consolidated housing to my specifications. Attached are the mock ups I made in photoshop of my ideal pedal. It is a synthesis of the following: Red Eye Twin Trinity Preamp (Quantity 2) TBD tuner Wampler Ego Compressor TC Hall of Fame Mini

    $584 (Avg Bid)
    $584 Avg Bid
    9 bids