Job printed circuit board pcb jobs

Filter

My recent searches
Filter by:
Budget
to
to
to
Skills
Languages
Job State
23,281 job printed circuit board pcb jobs found, pricing in USD

1) Detaled Description of 50 Raspberry Pi Projects with Photos [no copyrighted content] 2) All Linux Commands For Raspberry Pi 3) Raspberry Pi Installation Process wit...Pi 3) Raspberry Pi Installation Process with Photos [Detailed Description] 4) Raspberry Pi Components Photos and Description [Including Components that were added later in circuit

$23 (Avg Bid)
$23 Avg Bid
5 bids

Smd pcb development. modifying the current PCB design with Op amps resistors and other modules.

$293 (Avg Bid)
$293 Avg Bid
17 bids

...artists involved. Each of the images that I can share with you were created by myself, iin between the time that I was spent speaking with the Chinese in Shenhen about the circuit boards and how we would be tying everything together. The technology is sound, we now just need to show it off. If you enjoy working on next-generation type technologies, this

$1032 (Avg Bid)
$1032 Avg Bid
53 bids

Need a custom control board designed to control a main led light source, a secondary led light source that activities with impact, power switch, and speaker. The board needs to be able to play the sound files based on the movement of the device. No more than 0.8" wide board. The board and speaker need to fit inside a.0.9" wide cylinder.

$157 (Avg Bid)
$157 Avg Bid
11 bids

I need a pcb board for a wifi device that interacts with my website.

$182 (Avg Bid)
$182 Avg Bid
24 bids

I have 2 JPG images, one of the top of a small circuit board and another of the bottom of the same one. I was wondering if someone could create Gerber files out of these so the pcb can be manufactured, thanks The files are attached bellow.

$28 (Avg Bid)
$28 Avg Bid
13 bids
Solar heated jacket 5 days left
VERIFIED

Solar heated jacket for assebling. I'm attaching scheme for making jacket. Parts for jacket should be available here: https...1122657&needQuery=n and here: [url removed, login to view]+bank Voltage, Ampers and Watts and whole circuit with chargers I'm leaving to your decision.

$912 (Avg Bid)
$912 Avg Bid
12 bids

Design a TR21 flex PCB and output Gerber files and 3D PDF.

$159 (Avg Bid)
$159 Avg Bid
10 bids
Flex PCB design 5 days left

Design a TR20 flex PCB and output Gerber files and 3D PDF.

$168 (Avg Bid)
$168 Avg Bid
13 bids

Circuit simulations using Orcad software

$19 (Avg Bid)
$19 Avg Bid
2 bids

We would like to hire someone to design (no PCB needed, only schematic but the simulation needs to be as accurate as possible) a crystal notch at a specific frequency (in the MHz). We already have the quartz, we also have every parameters of each piece (Fs, Fp, Cs, Cp, Q, Rs ...) This filter needs to be matched at 50ohm IN and OUT. Attenuation

$185 (Avg Bid)
$185 Avg Bid
12 bids
PCB design 4 days left

I need a relatively simple PCB designing for a short POC run. The design is a 200 pin SO-DIMM socket with each pin tracked out to a pad large enough to solder by hand. It needs to be as small as possible while remaining usable.

$80 (Avg Bid)
$80 Avg Bid
4 bids

...experienced EU based PCB designer for the following "mSATA to USB 3.1 Type-C Adaptor (mass storage USB 3.1)" This is custom designed mSATA (SSD) to (Mass Storage) USB 3.1 (Type-C) adaptor. - Design based on ASMedia USB bridge are preferred - Design based on Texas Instruments USB bridge is the second preference - Maximum 4 layer ([url removed, login to view]) PCB i...

$943 (Avg Bid)
Urgent NDA
$943 Avg Bid
6 bids

I need a simple 8 circuit common bus pcb designed. Each of the 8 common busses should have 18 holes that can accommodate 18AWG stranded wire. I'd also like there to be a test point for each of the 8 busses. The test points will need to be multimeter probe friendly so that a technician can plug one of the multimeter's probes in one test point and

$24 (Avg Bid)
$24 Avg Bid
29 bids

I am looking for an electronic engineer to design a circuit and making PCB for manufacture

$128 (Avg Bid)
$128 Avg Bid
20 bids

Im looking for a developer based in South Africa (must be based in SA) to develop a job site/job board - similar to careers24. I do not know what skills are required.

$728 (Avg Bid)
$728 Avg Bid
41 bids

Hi, I have 3 PCB files that need modification in PADS. Changes have already been made in Altium for same PCB files, but i want same changes to be done in PADS.

$140 (Avg Bid)
$140 Avg Bid
19 bids