Microcontroller based company jobs

Filter

My recent searches
Filter by:
Budget
to
to
to
Skills
Languages
    Job State
    3,771 microcontroller based company jobs found, pricing in USD

    Hello , I need a schematic for my battery charger and backup power supply circuit, this is essential for microcontroller-based project. I have to use this components: Micro USB shield Battery regulator MCP73833 Voltage regulator TPS76933DBVR BATERIA RECARREGÁVEL LI-PO 3.7V 1.050A NIMO

    $48 (Avg Bid)
    $48 Avg Bid
    24 bids

    My electronics knowledge is very limited but I'm trying to build a light setup for a 12V car. I have six different lights that need to be able to flash or stay on continuously. The lights will be controlled by 12V SPST switches. 1. Two headlights that will either do alternating flashing or stay on continuously. 2. Two Fog Lights that will only do alternating flashing when the headlights ar...

    $25 (Avg Bid)
    $25 Avg Bid
    31 bids

    Fasetto is a company making ultra-portable microcomputers with large storage and wifi. We currently use the IMX6 quad core MCU with Linux already ported into the hardware. We would like to build an abstraction layer to isolate the app team from the hardwarre as well as implement an efficient process controller to optimize the use of the 4 cores

    $613 (Avg Bid)
    $613 Avg Bid
    5 bids

    Hi Bijan M., do you have any experiences with INFINEON microcontroller and PMSM motors?

    $11 (Avg Bid)
    $11 Avg Bid
    1 bids

    Hi, I am have an ARM Cortex STM32F103C8T6 and voice module WTK6900B01that I need to have programmed for pcb.

    $260 (Avg Bid)
    $260 Avg Bid
    27 bids

    I need some design advice for my first electronics project: The goal is to control the power supply of the indidual bays of a hard drive backblane. [[ See attached image first ]] The MCU should control 15 identical switches. Communication between the MCU and the host PC should happen via USB. USB should also be be used for the power supply. The whole design should be optimized for minimum power...

    $30 / hr (Avg Bid)
    $30 / hr Avg Bid
    21 bids

    I need an expert on Arduino. I need the microcontroller to calculate the distance between two coordinates chosen from 1 gps local and another remote. and display the distance in a Display. More details to be provided to preferred freelancer

    $34 (Avg Bid)
    $34 Avg Bid
    30 bids

    -Program microcontroler ATMEGA8-16PU -3 Actuators -3 HALL sensors input (position of actuators) Signal is DIGITAL on sensors - each actuator has end switch on up/low limit - Soft start on Actuators - 6 button hand control 3 actuators up/down Hand control separate from foot control - 6 button foot control 3 actuators up/down 3 taster preset programmable positi...

    $91 (Avg Bid)
    $91 Avg Bid
    7 bids

    ...written in the C programming language incl. PICkit 3 In-Circuit Debugger/Programmer. The code must be entered via the keypad. The data sheet is in the upload files. The microcontroller must be a 16F887. The LCD of the PICDEM ™ 2 PLUS DEMONSTRATION BOARD must serve as the output. If the code has been entered correctly, a relay must switch to simulation

    $127 (Avg Bid)
    $127 Avg Bid
    14 bids

    ...software to clone a chip credit card 4 days left Project name: Smart Card EMV / EMV ISO-7816 & Smart Card Java Card Software Engineer & Programming & Ecectronic Engineers & Microcontroller & Cryptography Look what I need : 1 PIN Project I need a Software with wich I can just read the PIN from a Smart Card ( a Bank Card ) wich can be a SDA or DDA card Like

    $194 (Avg Bid)
    $194 Avg Bid
    2 bids
    $201 Avg Bid
    1 bids

    ...proposed sensor(s) is/are to be able to measure the concentrations of Nitrogen, Potassium, and Phosphorous in wet soil. The sensor(s) should be able to be integrated into a. microcontroller. A specially skilled instrumentation engineer with experience in designing and building sensors is most appropriate. Further details can be shared on ward of the prpject

    $216 (Avg Bid)
    $216 Avg Bid
    4 bids

    I need to control 3 motors via Bluetooth using atmega 328 microcontroller or on arduino mega/uno board. only need simulation and code file. Experienced persons bids only mentioning in proposal past projects done if any.

    $26 (Avg Bid)
    $26 Avg Bid
    30 bids

    ...have unknown value (LSI has separate power supply and most of the time will be ON) in counter register for each single power up for Target Board (ez430). The register in microcontroller that will be holding internal virtual counter that will be with reset feature that set value to zero. The actual count in virtual counter goes both directions to positive

    $30 - $250
    Featured Sealed NDA
    $30 - $250
    12 bids

    Program microcontroller or  any low cost programmable to operate touch screen, Bluetooth, wifi, ir device and rf devices in hardware.

    $599 (Avg Bid)
    $599 Avg Bid
    5 bids

    Project name: Smart Card EMV / EMV ISO-7816 & Smart Card Java Card Software Engineer & Programming & Ecectronic Engineers & Microcontroller & Cryptography Look what I need : 1. PIN Project I need a Software with wich I can just read the PIN from a Smart Card ( a Bank Card ) wich can be a SDA or DDA card. Like everybody

    $3545 (Avg Bid)
    $3545 Avg Bid
    10 bids

    When there is an accident the car will the object and the switch or the IR sensor will detect the crashing, and will send the command to the microcontroller. The microcontroller will process the command according to the provided code and logic. The command will be send to the GSM module which will send the data to other care through the SMS message

    $18 (Avg Bid)
    $18 Avg Bid
    5 bids

    ...by functionality and connect together inside a water-tight, metal housing. There are PCBs for: CPU, SRAM Memory 8MB, Analog section, Measuring sections, Sensors. Main microcontroller which is used so far is PIC16F74 operated on 5V and it should be replaced by MSP430 line (TBD which one exactly). DEVICE FIRMWARE The firmware is written in assembly

    $1368 (Avg Bid)
    $1368 Avg Bid
    20 bids

    Building a pan/ tilt camera setup Reciever ...mounted on top side of continuous servo as i have built a slip ring that will provide 12v without cables twisting I will need programming of atmel Microcontroller that is used Needed. Code for microcontroller Pcb manufacturing files Pcb diagrams Possibly working prototypes of transmitter and reciever

    $1749 (Avg Bid)
    $1749 Avg Bid
    18 bids