Oled design jobs

...LED lightbulb. This is a simple demo project to show WiFi connectivity using the ESP32 microporcessor Using ESP32, 64x128 oLed, one button and 3 LEDs, 10K potentiometer, 1602 LCD (non I2C) Dial in R color using potentiometer 0-255 – Press button, show brightness on RED LED Dial in G color using potentiometer 0-255 – Press button, show brightness on GREEN LED Dial in B color using potentiometer 0-255 – Press button, show brightness on BLUE LED Colors will show on individual LEDS after each button press Press button again to “send” color setting the WiFi LED light bulb and show final mixture values on the 1602 LCD Restart color mixture process showing values on the oLed Ideal Skills and Experience: - Beginner's level proficiency with ESP...

...am seeking a talented and experienced electronics engineer to design a custom electronic circuit board for an experimental project. The primary functionality required for this board is the ability to accurately calculate the phase angle between two input signals and to show the result on an Oled screen. Key requirements and specifications for the project are as follows: - Intended use: This board will be used for an experimental project. - Functionality: Accurate phase angle calculation between two input signals. - Frequency range: The input signals will be in the very high frequency range of 150Mhz. The ideal freelancer for this project should have: - Strong background in electronics engineering, particularly in circuit design. - Experience with high-frequency si...

...the electrical components within the frame/ arms. • To produce a finalised and refined prototype that seamlessly integrates the thermal imaging and electrochromic systems within the glasses, maintaining comfort and functionality as well as the design aesthetics of the concept artwork. Technical Requirements: • Thermal imaging capabilities – the glasses will feature two powerful thermal imaging cameras and sensors, to process and display high-resolution imagery onto the lenses. • Head up display (HUD) – the glasses will feature dual, full-colour micro-OLED displays, covering as much of the lens viewport as practicably possible, to overlay high-definition imagery and edge detection whilst still being able experience the ‘real world’. &...

I'm seeking an expert electronics engineer to design a circuit for an Arduino-based, battery-powered hand warmer device. This design must incorporate intelligent functionality for temperature and run-time control. Key requirements are: * The device should warm up to 42°C and maintain this for one minute. After that, it should shut down and take a break for an hour (this cycle to repeat continuously). * The unit must have a maximum temperature limit of 45°C. * There should be a 0.96 inch OLED screen displaying temperature and time status. * The design should include push button control to start the skin warming and once the push bottom pressed again the program should quit off the warming cycle . * Using Normally closed temperature switch 45 deg. ...

I'm currently looking for a skilled Arduino engineer to assist in using an Arduino Nano, hx711, and ssd1309 screen to display readings from a load cell. Key ...ssd1309 screen, and the load cell have been procured and are available for the project. - The desired unit of measurement for displaying the load cell readings is in Kilograms (kg). - The hardware setup will primarily be used in indoor conditions. Ideal Skills and Experience: - Expertise in Arduino programming and interfacing. - Previous experience working with HX711 load cell module and ssd1309 OLED screens. - Strong understanding of units measurements, specifically kilograms. Please place your bid considering these specifications, and include any similar projects you’ve worked on. Looking forward to a succes...

I'm searching for a professional who can design and develop an OLED display driver that's compatible with STM32 or another microcontroller. This task will require both hardware and software handling proficiency. Key Tasks: - Create a driver for an OLED display with a support of SPI interface. - The driver must be able to support a maximum display resolution of 128x64 pixels. - Ensure that the developed driver aligns seamlessly with STM32. The ideal candidate for this project will have: - Extensive experience in working with STM32 microcontrollers. - Strong knowledge and experience in SPI interface. - Experience in developing display drivers, especially for OLED displays. - Exceptional debugging and troubleshooting abilities. - A good understanding ...

I'm in need of a skilled consultant to help with the design and functional specification of an Augmented Reality (AR) OLED HUD (Heads-Up Display). While I have not outlined the specific purpose in this job posting, I am open to the consultant's input on its possible applications including navigation assistance, vehicle information display, or gaming experience enhancement The AR OLED HUD display might include features like GPS navigation, a speedometer and a fuel gauge. However, I am open to other functionalities that can enhance its utility and appeal. Freelancers bidding on this project should be well-versed in AR and OLED technology, with a strong understanding of the requirements of a Heads-Up Display. In your application: - Please provide exam...

Colloidal Silver Generator The main idea is to build the most advanced colloidal silver generator available today. User might have no knowledge of chemistry or electronics so these skills should not be required to make perfect colloidal silver every time. Generator might contain a microprocessor unit (may be a ESP32, Arduino, ATmega, PLC..) UI may be OLED display, touch screen or mobile app which will bring computer controlled precision and versatility to the process and greatly simplifies operation. It Will offer unrivaled accuracy and versatility together with unparalleled ease of use. Its internal computer together with its custom hardware will precisely measure the amount of silver removed from the electrode so the generator should knows exactly when to turn off power to the ...

Hey, I am looking for someone who will Design Hardware for ESP32 (Lighting with WS2815). I will do software by myself 1. Power Supply - Battery-operated - 2x18650 batteries connected in series - Ability to be powered by 12v (mains adapter) 2. StepUp to 12v for powering the programmable WS2815 LED strip (unless someone convinces me that it's better to use WS2813 with StepDown) - Power consumption for the LED strip, at least 50W, max ~200W - Logic level converter required from 3.3v -> 5v 3. StepDown for powering the ESP32 4. OLED display 128x64 I2C 5. Measurement of power supply voltage and power consumption 6. Power activation via a mechanical switch 7. 2x rotary encoder with button 8. Connector for programming the ESP32

...am looking for an adept and creative individual with proficiency in utilizing the Raspberry Pi systems and OLED technology. The emphasize of my task is: - Designing and programming a pair of 4-inch or 4.5 inch round OLED screens, to serve as animated cat eyes in my costume head attached. . - These screens should ideally function on a platform like Raspberry Pi. - The animation must be smooth, lifelike, and engaging to create a convincing illusion of a cats eyes. - Prior experience with animation and the Raspberry Pi platform would be highly beneficial. All need to be used in my cat head costume during parades. An individual who possesses a strong grasp of Raspberry Pi programming, OLED screen operation, and advanced animation skills will be perfect for this job. ...

...conceptual design focused on product visualization. The product in question is a technological gadget and the design should include surface texture details. Ideal Experience and Skills: - 3D designing and modelling - Product visualization - Attention to detail - Proficient in adding high-detail surface texture to models - Experience with technological gadget designs Your task will be to provide a realistic and intricate 3D design that effectively communicates the gadget's aesthetic and functional design aspects. We have the first view that we visualized and basic model just based on the components dimensions. However, we wish the device to be more like as shown in attached visualized images. Just that the dimensions can vary and we can get that righ...

...unique ID and temperature. - 8-bit Screen: To display the determined parameters. Type of screen (LCD, OLED, E-ink) can be recommended by freelancer based on their experience and best practices. - Bluetooth Connectivity: To transmit data to mobile devices. Specific Data to Display/Share: - Charge Percentage - Unique Battery ID - Temperature Data Update & Display: - Data should be updated and displayed on a demand basis. Ideal Skills: - Experience with Internet of Things (IoT) - Sensor development & integration - Knowledge of lithium-ion battery metrics - Bluetooth connectivity mechanisms - Screen technology (LCD, OLED, E-ink) In your proposal, please include your expertise with IoT sensor design, battery analytics, Bluetooth connectivity options, and you...

...an experienced engineer to design and develop a multi-functional embedded system. This project involves crafting a prototype of a versatile meter capable of measuring and logging a range of parameters. Here's what I need: This is an Universal Multi Function Meter which can able to read AC - 1 Phase 3 sets, AC - 3 Phase & 4 Wires 3 sets, DC - 4 sets , Temp- 5 Sets, Pressure 3 sets, Flow-3 sets, Vibration-3 sets, Speed - 3 sets, Sound Noise -3sets, all these data can measure through respective sensors and display in OLED and end the parameters to the remote through RS 485 data logger. Key Features: - Energy, voltage, and current measurement capabilities. - Extend measurement to AC & DC, temperature, pressure, flow, vibration, speed, and sound noise. - Utilize an...

• Design a hand-held device that could be the interface for users Male Users and subscribers to The Best Male Platform --that we are building the algorithms for the platform • Creating a handheld device for The Best Male Platform would involve a blend of functionality, usability, and connectivity. Here's a conceptual design for the device: Design Overview: Name: The Best Male Connect/TBM Messenger Appearance: Sleek, ergonomic design with a durable matte finish, available in various colors. Screen: A high-definition, touch-sensitive display (5-inch OLED) for crisp visuals and smooth interaction. Interface: Intuitive UI designed for easy navigation. Main features accessible via icons for messaging, profile, algorithm insights, communit...

Write firmware for STM32 blue pill with small OLED and rotary encoder. Must have experience with STM32 programming. We do NOT want Arduino programming. All details are in the attached document. Please add word STM32 at the top of your proposal to confirm that you have read the project description. Let us know if you have any questions. Thank You !

I need to build a digital clock with a matrix(1088AS) to show the time, an oled screen to fix the alarm and a bipper with an arduino nano

i am looking for an Arduino professional that can make a digital clock using a led matrix (1088AS), an RTC, and an oled screen.

...- Speedometer - Fuel Level - Temperature - Boost Gauge - Oil Temperature - Time -design the GUI interface -Display on OLED -3 buttons Up Down Enter -electronic components that convert real-world measurements into electrical signals) PCB board design after complete Design/Layout: While I do not have a specific design in mind, I have a rough idea of how I want the gauge to look. I am open to suggestions and creative input from the developer. Ideal Skills and Experience: - Proficiency in Arduino programming - Experience in designing and developing custom gauges - Familiarity with car metrics and their integration with Arduino - Ability to create an aesthetically pleasing and user-friendly gauge design - Attention to detail and ability to...

measure the pressure of the tires and the air compressor creating a project with Arduino NANO 5 air pressure sensors display oled on the display show the 5 pressure measurements

Using a wemos lolin lite esp32 development board how to wire to a 128x64 display with controller SSD1309 that has connections VCC, GND, DIN, CLK, CS, DC, RST give an exact wire pin out to the Wemos. You must produce functioning code that will display a bitmap image on the display. Here is the oled display: https://www.amazon.com/waveshare-1-51inch-Transparent-OLED-Independent/dp/B0B8N46G24/ref=sr_1_3?crid=1PPE3UAGWPTBZ&keywords=transparent+oled&qid=1700370317&sprefix=transparent+ole%2Caps%2C88&sr=8-3

I have an esp32 Development board with an mpu6050, micro sd card via I2c, an OLED via spi that is 128x64. I need you to develop an Arduino sketch for this project. I have already created the base code for the example. Everything is documented and attached below. Please read the documents attached below.

...freelancer to design an Arduino based IR pulse recorder with playback ability. The purpose of this project is to record and analyze IR pulses. Preferred Skills and Experience: - Proficiency in Arduino programming using Arduino IDE - Experience with IR pulse analysis - Knowledge of circuit design and implementation - Familiarity with IR pulse frequency ranges and analysis Requirements: - The Arduino based IR pulse recorder should be able to accurately record and analyze IR pulses within the desired frequency range of 50hz to 5000hz, with the ability to playback pulse patterns recorded/stored. - IR wavelength is 904nm (photodiode SFH203FA is required) - Project should be able to record the pulses detected to an SD card and display the following on an attached ...

I am looking for an IoT developer to build various projects for me. As a test project, I would pay you to complete a simple project to open and close a door for a chicken coop. I will send you a detailed requirements document. It's a straightforward IoT project that neither uses WiFi nor Zigbee. Instead, it will have an OLED display and a keypad.

Please read the requirements document attached below. You will need to program bitmap graphics by constructing arrays. You will display graphics to on oled screen that is 128x64 and have display functionality that is using the mpu6050 accelerometer. Looking to have this arduino sketch completed asap.

I am looking for a design for a Universal Solar Grid Hybrid EV Charger. There will be dual source input 230V, 50Hz Grid and Solar 90V - 150V DC input. Desired Output Voltage and current: - Dual output of 60V DC @ 15A and 72V DC @ 15A together Charging Speed: - Fast Charging, with a desired charging time of 1-3 hours EV Connector Type: - CCS Combo 2 (Combined Charging System) Skills and Experience: - Experience in designing EV chargers - Embedded system design and development of Hardware schematic, pcb, bom, Firmware code development and prototype testing. - Knowledge of different EV connector types - There should be OLED display and RS485 communication to remote. - The charger should design with suitable alarms, protection and trip...

Looking for someone witch are willing to design model for 3D printing. Here is an example of what I'm looking for :

Circuit conditioner for force sensor. This is a 2 part project, I need a simple PCB desgined as well as a arduino programming. The PCB will be enclosed in a billet aluminum case that I will make myself. Arduino; It will use a 128x64 OLED Display with I2C and 3 push buttons for user setting. Push button are Up, Down, Menu/OK. The arduino will feed 5v to the force sensor and read the analog voltage coming back. There is 6 setting to be set by user; - Resting voltage reset --> Set the voltage of the force sensor with no forward or reverse force applied - Pull Force --> Set the voltage when force sensor is being pulled - Pull Force Deadband --> Set the deadband of the pull force - Push Force --> Set the voltage when force sensor is being pushed - Push Force Deadband --> ...

Maranon is looking to potentially hire a contract electrical engineer. We are bidding several jobs that will require part time work. These products will use CMOS cameras and micro-OLED displays. We would like an EE who has experience designing circuits to drive the camera and display. We expect to start in approximately April of 2024 and need completion by July 2024. Must be US Citizen or Green Card Holder. Responsibilities Read and interpret CMOS camera and micro-oled technical data packages and design and valid circuits that take drive the camera and display and transfer imagery from the camera to the display. Be able to layout and route flex circuits. Define appropriate micro-connectors. Interrelate with Maranon opto-mechanical engineer. Qualifications Bachelor...

Hello? I have few questions before I consider buying services , if you would be so kind to respond :) Basically I would need you to make logos for Oled screen using language based off of C , I can provide some guides & examples of it being used It can be done using values like this images const image xxx = {72, 64, 0x00, 0x43 Also stuff like circle_oled(x, y, radius, fill, color); And some others... Would you be interested in trying making some custom logos? How much would you charge for making it? How long to deliver? We can discuss ? BTC

Hi Philipp, Would you be interested in providing me with five Can-Bus shield assembled boards: - LORA32 868/915Mhz Module SX1276 ESP32 with Oled-Display - GPS with external antenna (connector) - GSM/GPRS with external antenna (connector) - SD card to save offline - a toggle button to set the mode to Rx/RxTx on the bus - power from the can-bus (if possible; if not, from battery) - two RGB LEDs (Power and Mode) - form factor set to a reasonable minimum You would provide me 5 working boards and the a test-code to test all functions of the device. The boards will have the development name "EFFORD AG" and the model name "arCan pro" Due date has to be 2023. Knowledge pool: -

Hi Philipp, Would you be interested in providing me with five Can-Bus shield assembled boards: - LORA32 868/915Mhz Module SX1276 ESP32 with Oled-Display - GPS with external antenna (connector) - GSM/GPRS with external antenna (connector) - SD card to save offline - a toggle button to set the mode to Rx/RxTx on the bus - power from the can-bus (if possible; if not, from battery) - two RGB LEDs (Power and Mode) - form factor set to a reasonable minimum You would provide me 5 working boards and the a test-code to test all functions of the device. The boards will have the development name "EFFORD AG" and the model name "arCan pro" Due date has to be 2023. Knowledge pool: -

Hi Philipp, Would you be interested in providing me with five Can-Bus shield assembled boards: - LORA32 868/915Mhz Module SX1276 ESP32 with Oled-Display - GPS with external antenna (connector) - GSM/GPRS with external antenna (connector) - SD card to save offline - a toggle button to set the mode to Rx/RxTx on the bus - power from the can-bus (if possible; if not, from battery) - two RGB LEDs (Power and Mode) - form factor set to a reasonable minimum You would provide me 5 working boards and the a test-code to test all functions of the device. The boards will have the development name "EFFORD AG" and the model name "arCan pro" Due date has to be 2023. Knowledge pool: -

Change Display From .96 to Inland 128x64 1.3" LCD and Mounting Bracket / Screw Holes Change 12 Key from JCAR to DIGIKEY Part Number #1568-1856-ND Change Rotary Encoder Bracket To Fit Inland Rotary Encoder KS0013 Change Battery Bracket To Allow MakerFocus 2000mAh All the dimensions will need to be adjusted with their mounting screws as well to accommodate the new parts

I am looking for someone who can help me set up my TV/Video/Yamaha Receiver RX-V679. I specifically need help with connecting devices and cables. Requirements: - Experience with setting up TV/Video/Yamaha Receiver RX-V679 ...connecting devices and cables. Requirements: - Experience with setting up TV/Video/Yamaha Receiver RX-V679 - Knowledge of different types of cables and how to properly connect them My system use to be setup fine. But now I seems to have got the cables mixed up and I can't get the Xbox and Switch to work via the receiver. Also, the left and right middle speakers don't seem to have sound. The TV is an OLED LG (C1 I think). I will pay $22 as it should only be simple if you know what you're doing I need someone who can help me via video call...

We are looking to replace a Graphics LCD display with 320x200 pixel resolution using a SED1330/1335 Controller with a modern TFT or OLED based solution with 400x300 pixel resolution . The scope of the project will be to suggest a low power ,MCU suitable for this task or a FPGA/CPLD based solution , develop and debug the code to convert the data from the SED1330 commands to serial commands the new display can process and scale the data to fit the higher screen resolution . All hardware design will be performed by us

...developing bell systems for schools and should be able to provide a system that will meet the following requirements: Range: - The system should cover the entire school building. Features: i want an IoT school bell system with the function rtc time and using touch keypad I can do customisation in time I can set time using cloud. 15 to 20 time schedule for timing. Cpu:- Nodemcu Display :- Oled 128 x 64 RTC MODULE:- ds3231 Keypad :- ttp229 touch keypad Relay And also want menu system like following:- 1) Set time / date 2) Set Time Table 3) View Time Table 4) Holiday 5 ) Bell settings In Bell settings there will be two option 1) Short bell ( in that 2 sec bell two or three time that I can adjust) 2) Long bell ( as per above but duration is 5 ec each bell - The system should have ...

Hi, I have a working arduino project involving : Esp32 I2s microphone I2s ampli + speacker Gps module Gprs module Piezzo electric buzzer 5 buttons Oled 128x64 screen Led Pir captor Microwave and light intensity captor Battery I am looking for someone able to design the circuit and all the needed element to create a first custom pcb iteration (including chip assembly). Double check and fine tune of my arduino code is also needed.

I am looking for someone to fix the sound issue I am experiencing on my Asus Zenbook 14 OLED Q409Z laptop running Ubuntu 22.04.2 LTS. Despite trying some troubleshooting steps, the sound still does not work. I am specifically trying to use the built-in speakers. (sounds were working perfectly on windows 11) Ideal skills and experience for this project include: - Proficiency in Ubuntu - Experience troubleshooting sound issues - Familiarity with Asus Zenbook laptops - Attention to detail and ability to diagnose and fix technical issues

I am looking for a freelancer to design and develop - Enhance / modify current design of our Raspberry Pi I/O Extender board. -- Adding into it a 'daisy chain feature for the daughter boards(see below). - Design 'daughter' / 'child' boards which can be hooked up in a chain talking over I2C, SP2 etc Function: - Daisy Chain / Connect through RJ45 Cables / headers. (Data and low power) - Have a high power input / output for motor. (opto isloated) - Input pins, and output pins. - Dip switch block for 'position' in node chain / daisy chain. - OLED screen for displaying basic Info(2.42 inch) - Control string of WS2812 LED's OLED screen will simply displays 0-999. and basic connection / startup / config options. The...

I am looking for an experienced Arduino developer to help me generalize my i2c code. I am using a specific Arduino board, which I will specify. I have some code that actually manages 16 i2c OLED screens using 2 i2c muxes, but want to code a program that manages the 8 possible muxes by address. The code receives some midi sysex signals (screen number, text), and sends it to the corresponding screen. So in summary I want to convert the code supporting 2 muxes into a generalized one for 8 muxes, stored into an array of references, and tidy up the code in general. The original code will be shared accordingly.

Request details Development in the Arduino IDE for the QTpy module used as an SPI slave ontroller for an OLED display The wiring for the SPI bus on the QTpy uses Sercom0. I've installed the available SercomSPISLave library but the proper variant.h and files assigns PIO_SERCOM_ALT SERCOM2 instead. In either case I'd like to change the existing SPI master to an SPI slave keeping the same wiring and changing the Output pins to Inputs. I can't seem to make the example code to compile after making the appropriate changes and I could use some help!!!! Deliverables Review my code or create it separately.

Please Sign Up or Login to see details.

My device has esp32 processor, simcom A7672E gsm module. In addition, there are 8 digital inputs made using 74hc165, 8 digital outputs made using 74hc595, 3 analog inputs, 2 analog outputs, 1 rs485 port, 128x64 oled display working with I2C. The system is exchanging data with http query. Processing the Modbus Tcp/Ip queries that will come from the gsm module, which has a fixed-ip sim card, over the uart, in transparent mode, on the inputs and outputs on the desired, and giving the necessary response.

Hi there, I need an electrical engineer to complete a small project that involves a Pico and a Pi 4 and an OLED display. Would someone be willing to help me complete my project? There are a couple of bugs with the image being shifted/corrupted that need fixing. The outstanding features list left to be completed can be found at the bottom of the GitHub repository. Kind regards Ben

Hello, I'm looking for someone to help me out with a project that involves an nRF52 microcontroller. I need someone to help with the programming and the main feature of this project is wireless communication and OLED displya. I have finished PCBA and write about 60% of frimware. You can see block shem in the attament I need person who have experience with NRF52.

I need someone familiar with the u8g2 library for the SSD1306. I need simple functions to do the basic stuff without troubles. Something like (“Hello”) should work. You will propose what you consider the basic functions (whatever is easy to do using the u8g2 library). Please write OLED at the top of your proposal to show that you have read the description. This will likely lead to many more jobs with us. Thank you !

I am looking for someone to help enable OLED display on the GeeekPi Raspberry Pi Mini Tower Kit i recently purchased. here is the link of the case

I need someone to design a PCB in Altium with an OLED display and SSD1306 controller. I2C connection through 4-pin header. It is very similar to many modules you can buy online so this part is easy. But I need someone who knows where to buy/source the parts and how they will get assembled (special instructions to PCB manufacturer, how the OLED stays in place, etc) The goal is to make a small prototype run of PCB. Please only apply if you can help me get a real working PCB in my hands. It should be trivial if you have done this before. This may lead to more projects with us. Thank you !

Assist in completing a project as described in the exercise. Our scope includes all programming aspects and answering related questions about the keyboard and theremin (reading the frequency and displaying it on screen), metronome (changing beep in real-time, displaying frequency on OLED), and GUI. -> Pg. 10 Rodrigo: - Client: This part is entirely analog and must be assembled by the client. -> Pg. 11 Rodrigo: Simulate the circuit in Proteus and send the frequencies of each button. Client: Obtain the frequencies of the real circuit on the oscilloscope for comparison. -> Pg. 12 Rodrigo: Provide a code in Arduino to obtain the frequency and display it on the Serial Monitor of the Arduino IDE. Client: This part is entirely analog and must be assembled by the client and the ...