Pcb assembling job work outsourcing company jobs

Filter

My recent searches
Filter by:
Budget
to
to
to
Skills
Languages
Job State
11,137 pcb assembling job work outsourcing company jobs found, pricing in USD
Java Animation Cubes 6 days left
VERIFIED

I require a Java program that creates an animation of cubes randomly assembling themselves into one big cube. The smaller cubes should be flying in from the sides. Something like this, but needs to be X, Y, Z axis. [url removed, login to view] The program should display the animation and also save the animation as a movie (mp4

$27 (Avg Bid)
$27 Avg Bid
7 bids

Smd pcb development. modifying the current PCB design with Op amps resistors and other modules.

$293 (Avg Bid)
$293 Avg Bid
17 bids

I need a pcb board for a wifi device that interacts with my website.

$182 (Avg Bid)
$182 Avg Bid
24 bids

I have 2 JPG images, one of the top of a small circuit board and another of the bottom of the same one. I was ...have 2 JPG images, one of the top of a small circuit board and another of the bottom of the same one. I was wondering if someone could create Gerber files out of these so the pcb can be manufactured, thanks The files are attached bellow.

$28 (Avg Bid)
$28 Avg Bid
13 bids

Design a TR21 flex PCB and output Gerber files and 3D PDF.

$159 (Avg Bid)
$159 Avg Bid
10 bids
Flex PCB design 5 days left

Design a TR20 flex PCB and output Gerber files and 3D PDF.

$168 (Avg Bid)
$168 Avg Bid
13 bids

Hi, i'd like to know if you can upload products in my e-commerce Magento version 1.6.2.0 I have .csv files where any products is linked to a photo but i i think i need some plug in to upload without problem. So could you do that? How much does it costs? I think i have 3000 products to upload with csv. Maybe better to control if thereis enought space . Thanks. Ale.

$10 (Avg Bid)
$10 Avg Bid
1 bids

We are working on a Arduino project involving a APDS-9960 sensor and Bluetooth kit from sparkfun. We require some one with interests in Arduino projects to assemble the PCB's, circuits and sensors and solder it. All modules, sensors, circuits, programs will be provided.

$207 (Avg Bid)
$207 Avg Bid
23 bids

We would like to hire someone to design (no PCB needed, only schematic but the simulation needs to be as accurate as possible) a crystal notch at a specific frequency (in the MHz). We already have the quartz, we also have every parameters of each piece (Fs, Fp, Cs, Cp, Q, Rs ...) This filter needs to be matched at 50ohm IN and OUT. Attenuation

$185 (Avg Bid)
$185 Avg Bid
12 bids

Assembling two different modules for dual sim phone: GSM and Sat-phone modules. Designing external sat antenna with connector. Writing script for maintaining sat module. Phone for sailormans, mountain climbers, areas without GSM broadcast.

$22 (Avg Bid)
$22 Avg Bid
5 bids
PCB design 4 days left

I need a relatively simple PCB designing for a short POC run. The design is a 200 pin SO-DIMM socket with each pin tracked out to a pad large enough to solder by hand. It needs to be as small as possible while remaining usable.

$80 (Avg Bid)
$80 Avg Bid
4 bids

...experienced EU based PCB designer for the following "mSATA to USB 3.1 Type-C Adaptor (mass storage USB 3.1)" This is custom designed mSATA (SSD) to (Mass Storage) USB 3.1 (Type-C) adaptor. - Design based on ASMedia USB bridge are preferred - Design based on Texas Instruments USB bridge is the second preference - Maximum 4 layer ([url removed, login to view]) PCB i...

$943 (Avg Bid)
Urgent NDA
$943 Avg Bid
6 bids

I need a simple 8 circuit common bus pcb designed. Each of the 8 common busses should have 18 holes that can accommodate 18AWG stranded wire. I'd also like there to be a test point for each of the 8 busses. The test points will need to be multimeter probe friendly so that a technician can plug one of the multimeter's probes in one test point and

$24 (Avg Bid)
$24 Avg Bid
29 bids

I am looking for an electronic engineer to design a circuit and making PCB for manufacture

$128 (Avg Bid)
$128 Avg Bid
20 bids

Hi, I have 3 PCB files that need modification in PADS. Changes have already been made in Altium for same PCB files, but i want same changes to be done in PADS.

$140 (Avg Bid)
$140 Avg Bid
19 bids

I would like to make a modular phone charger. If you have experience with PCB design and electronics feel free to respond! Please see attachment for requirements.

$222 (Avg Bid)
$222 Avg Bid
36 bids

Make a simple adapter board to split one power input into several high power lines.

$42 (Avg Bid)
$42 Avg Bid
7 bids

I need someone to either design a motherboard for me from scratch or work with the one that i have started designing in eagle. I would prefer the design to be made in eagle but other cad software's are OK too. the dimensions of the board should be in approximately a 2:1 ratio and can be any size smaller than 154/77mm. The board should be as thin

$200 (Avg Bid)
Guaranteed
$200 Avg Bid
2 entries