...apart with a 4-pin connector IN and 4-pin connector OUT. Each slave will have a 12V lamp attached and switched by a mosfet. The requirement is to make a plan on what microcontroller, ic's and other parts to use, and which technologies to use to achieve this. Create a prototype on ready made hardware like an Arduino or similar. And develop the code
We need to make a slave implementation of the m-bus protocols. (Meter bus see: [url removed, login to view] ) The microcontroller to be used is an 8 bit AVR ATmega324pb. M-bus interface chip NCN5150
the design is part of a project and it needs to be done asap. the simulations should be done for a microcontroller so the knowledge of C or assembly is a benefit. the outline of the design will be provided and has to be designed on OrCad.
... I need an electronic engineer skilled in Arduino, Raspberry Pi, WiFi, Bluetooth, PIC, PLC and professional in Electronics schematics and PCB design (Altium)–Circuit analyzing and debugging- Hardware reverse engineering - Firmware development –C++, C- microcontroller embedded system - EMC Compliance Consultancy - Test & Manufacture. They should be
...able to sync their internal clock with the server. Possibility to fix issues in the firmware and optionally add new features in the future without having to remove the microcontroller from every device. For this reason, devices support over-the-air upgrades. RFID cards are formatted Mifare cards with changed keys. Cards are preformatted and a unique
Use C...filtered CAN data on the SD card. Upload the data file from SD card to the server. The hardware is STM32 Nucleo-64 development board with STM32L476RG ARM Cortex-M4 CPU Microcontroller and Wi-Fi expansion board based on SPWF04SA Wi-Fi module. Development Environment(IDE) is System Workbench32 Programming language is Embedded C.
...voltage is 3 volts or 25 volts. For input capacitance use C3216JB1E336M160AC Place twenty in parallel. For microcontroller we specify use of NRF53832 The microcontroller will take a 0-5 volt input to regulate speed. The microcontroller will also have some inputs to measure current on two of the phases and DC input. The software will regulate
Remote control transmitter and receiver circuits for an audio stereo amplifier If you are interested in this project can you let me know and I shall send further information: i. Link to download the files for this project ii Schedule of work Please let me know if you would like any more information The budget is set to the minimum val...
...data transmitted is zero. This fluctuation of the LED light is detectable by Photo-detector. The LED light bulb used to transmit the data controlled by a microcontroller. This microcontroller switching the LED light converts the digital data to light waves which are then transmitted. These transmitted waves are received at the receiving end by a photodetector
...in EAGLE to delayed power that feeds an array of P MOSFET transistors. The delay is to allow enough time for the microcontroller to boot up without causing any P MOSFET to activate during bootup. Updating the firmware on the microcontroller is NOT an option. The current delay can be accomplished using a 2200uF Capacitor, however, we need a better
I'm looking for engineer or any experience individual to assist in making my lights rotate. To prov...experience individual to assist in making my lights rotate. To provide a system design drawing incorporating a gears and cam system with Arduino Pro mini (or relevant microcontroller)... Kindly refer to the attached document prior to contacting me.
...to handle 128 units with one IOT device (non collision support by statistic modulation duty cycle). low power microcontroller STM + ISM Transmitter + sheet metal antenna. Requirements: electrical engineer with experience in microcontroller and ISM Band RF design + firmware. preferred: experience in battery operated device development for low power
I am looking for a programmer to code my PIC microcontroller to drive a 6v dc motor using a PWM technique - The battery is in series - 3.6v x 2 = 7.4V LiPo 1000mAh The Motor Nominal voltage: 6VDC No-load speed: 13000rpm No-load current: 0.46A Stall torque: [url removed, login to view] Stall current: 11.8A The PWM technique should maintain the voltage at an average
I am looking for someone who is good in embedded system and can prepare gadgets based on IOT.
...this software to be developed using C or C++. Software setup/config/development for Atmel SAMW25 and SAME70 microcontrollers using atmel Studio 7. One program for each microcontroller type, two programs in total. Creating the base application, configure the pins, include relevant frameworks, connecting libraries and making the functions available for
Our company is just startup. Iam a hardware engineer with good knowledge of microcontroller, DSP and all sensors(Good Knowledge only on hardware). I need a person who can work from their home to create embedded programs. Iam comfortable with Microchip, Freescale & Atmel processors. All my projects are simple. One scope. Data anayisis