Stepper motor control using labview jobs

Filter

My recent searches
Filter by:
Budget
to
to
to
Skills
Languages
    Job State
    9,627 stepper motor control using labview jobs found, pricing in USD

    Looking for a simple program so that an Arduino (or RasberryPi) can control an AC motor. The system will need to be able to do the following: * Start and stop the motor * There will be mechanical limit switches that will shutdown the motor when tripped. * Restart the motor after limit switch has been tripped via UI (mobile application, Web UI etc

    $169 (Avg Bid)
    $169 Avg Bid
    12 bids

    I'm building a 3 axis camera motion slider and I need someone who can modify an existing sketch to suit different outputs and also add PS3 bluetooth control using the PS3BT.h library and the AccelStepper.h / MultiStepper.h libraries. This should be a pretty simple job for someone with the right skills as most of the sketch already exists.

    $32 (Avg Bid)
    $32 Avg Bid
    2 bids

    ...[login to view URL] USB C charging for batteries - (please recommend an arduino compatible one to allow charging control and monitoring via ardiono) must support USBC fast charging and ideally USB Power Delivery higher load charging using for example a laptop charger). Arduino board - (TBC based on above and below components). 2x Servo Motors OLED Screen

    $153 (Avg Bid)
    $153 Avg Bid
    6 bids

    I need IOT based motor On/off controller With 3phase indication and current measurement using app or website . Based on ESP 32/8266

    $190 (Avg Bid)
    $190 Avg Bid
    23 bids

    I would like someone to assist in deriving the formula for calculating the Thrust from a brushless motor if KV/RPM, Max Power, Propeller size, Voltage and Max continuous current was provided. Ideally suit a mathematician or someone with experience in doing such calculations.

    $35 / hr (Avg Bid)
    $35 / hr Avg Bid
    26 bids

    I need you to design a synchronous motor in FLUX 2D from cedrat. I have the full tutorial in english. The project have to be ready until 5th september. If you know to work whit this program please contact me.

    $183 (Avg Bid)
    $183 Avg Bid
    3 bids

    I want to make a programme to send and receive AM and BPSK waves at 51.2 khz on Raspberry pi3

    $163 (Avg Bid)
    $163 Avg Bid
    17 bids

    I need you to fill in a spreadsheet with data.

    $14 (Avg Bid)
    $14 Avg Bid
    1 bids
    labview DLMS 1 day left
    VERIFIED

    read/write data to Smart meter with DLMS protocol using labview

    $100 (Avg Bid)
    $100 Avg Bid
    11 bids

    ...Atmega2560 2) Servo Motor with driver (3Nos) 3) Stepper Motor with driver (7Nos) 4) M007 Touchscreen (HMI) Software for HMI: [login to view URL]!AouhlXXdprIt6x5TNRusQYstzHWT. (Use the latest version) Please find the data sheet of all attached along with the schematic of the PCBA. We need to create a simple program to control all stepper and servo motors

    $249 (Avg Bid)
    $249 Avg Bid
    17 bids

    arduino program to make a servo motor works wrt the flex sensor

    $121 (Avg Bid)
    $121 Avg Bid
    47 bids

    Project details: Using information provided via the links below, create a software package that is able to drive multiple stepper motors to specific relative positions, based off data received over Artnet or E1.31. Additionally, create solution for allowing the Raspberry to communicate via RDM status, error messages, and address/universe information

    $1065 (Avg Bid)
    Urgent NDA
    $1065 Avg Bid
    10 bids

    The main goal is to write a program for a ST32 mc that drives a stepper motor driver. (STEP-DIR) The hardware has a touch screen that requires menu system where user can set various settings. Although we already built the hardware but it needs to be changed as we want it to be able to save and store profile settings. Currently we don't have memory

    $1406 (Avg Bid)
    $1406 Avg Bid
    38 bids

    ...we are going to a fully automated test system, which is to be controlled by a DAQ system using a Laptop. I am looking for someone to write me two separate (but very similar) LabView programs for both of the test setups shown in the attached schematics. The LabVIEW program should have a simple interface, in which an operator can set the test pressure

    $3726 (Avg Bid)
    $3726 Avg Bid
    34 bids

    The total budget for CAD and FEM is Rs 3000/- The task is to design a Crane, do its CAD and analyze some critical part using FEM tool like ANSYS Overall/ General ○ Maximum Operating Temperature = 30oF (Room Temp) ○ Reliability should be about 99% ○ Minimum Fatigue FOS (modified goodman) for all parts has to be 2 ○ Assume a service (Bearing) life of

    $2 / hr (Avg Bid)
    $2 / hr Avg Bid
    18 bids

    We've developed an e-Bicycle and are in the process of developing a motor package, hence we need reduction gearing which will be made of a polymer. I have no idea what it's likely to cost to develop what we want (referring to estimated budget below).

    $2575 (Avg Bid)
    $2575 Avg Bid
    25 bids

    ...all parts has to be 2 ○ Assume a service (Bearing) life of 120 kh ○ Extend shaft 4 inches past housing with ½ inch transverse hole for a pin fastening ● Input (from electric Motor, McMaster Carr 5990K312) ○ Pin = 5 hp (max that can be supplied) ○ Win = 1750 rpms (assume constant and controlled) ● Output (from winch) ○ F LOAD = 2200 lbs ○ d cable = 0.5

    $57 (Avg Bid)
    $57 Avg Bid
    15 bids

    ...all parts has to be 2 ○ Assume a service (Bearing) life of 120 kh ○ Extend shaft 4 inches past housing with ½ inch transverse hole for a pin fastening ● Input (from electric Motor, McMaster Carr 5990K312) ○ Pin = 5 hp (max that can be supplied) ○ Win = 1750 rpms (assume constant and controlled) ● Output (from winch) ○ F LOAD = 2200 lbs ○ d cable = 0.5

    $108 (Avg Bid)
    $108 Avg Bid
    12 bids

    We are loo...YstzHWT System has the following sections: 1) Capacitive Touch Screen (7 Inch) - Will communicate with the main PCBA through (RS485) modbus protocol. 2) Servo (3Nos) / Stepper Motors (7Nos) - Will communicate with main PCBA through (RS485) modbus protocol. 3) Wifi (ESP) Contact us if you are well versed with the firmware development.

    $215 (Avg Bid)
    $215 Avg Bid
    12 bids