...every conveyors has 2 motors : one is the main and the other is standby. This is to avoid interruptions in case if one motor goes down. (another option is to have total 2 motors for all conveyors, please provide design ideas) 12) the motor speed is slow, e.g. 1m/min. 13) the motors should be located on one side of the conveyor to reduce the total width
I need you to develop some software for me. I would like this software to be developed using Python. 6 channel Relay station - Must be standalone program able to run on Arduino or Pi. User “program” to control 6 lamps. 3 blue lamps - 1 blue, 2 blue, 3 blue 3 red lamps - 1 red, 2 red, 3 red On and off at cycles with LCD GUI 3 total lamp groups- Group
I would like to get a PCB designed to interface a caliper with arduino. Basically the idea is to have a PCB where is possible to solder a sparkfun ardiuno promini and some additional components (transistors, resistors). All the system will be installed inside a plastic box and micro USB should be accessible from outside. Check attached scheme.
...wireless Arduino units driving stepper motors, to be activated with a simple remote control. I am new to the Arduino realm but can do the simple layouts and cut/paste code. There will be 4 of the following: Small Arduino units each running a single stepper motor (likely a 12v 28BYJ-48) in separate and independent enclosures. Individual motor ...
I'm a student who want to do a project to connect Arduino Yun to Atmel XMEGA A1U Micro-controller through SPI. XMEGA A1U Micro-controller will be connected to two RF micro-controllers AX8052F100 that are connected to two transceivers one acts as transmitter and the other acts as a receiver. I need someone who can write a code on Atmel XMEGA A1U to do
...small business. Necesito armar un website en Wordpress o algo similar para un servicio de “networking”. Debe ser sencillo, elegante, que permita hacer registro, tener chat, un motor de búsqueda y generar algo de contenido. Quiero usar plugins gratis y que ahorren tiempo. Además requiero apoyo en el diseño del logo. Deben tener disponibilidad para tenerlo
...control the speed and direction of an AC 1.5KW 3 Phase Motor with an Arduino. The 3 Phase Motor will be connected to a VFD of course, and the VFD will be controlled by the Arduino. There will be a control panel with the following: -Start/Stop Button, whenever Start Button is pressed it will allow the motor to start rotating based on Auto/Manual Switch, and
I need is a simple windows service to monitor the serial ...the program. need that as a windows service because it should run even there is no user logged in. also, need to write this from C# or VB.net and I need the code. I have an Arduino connected via serial port to monitor the ups and main power levels I need windows application to accompany that.
An Arduino board that produces inputed audio output through a speaker, and power two water proof servo motor. Speaker with volume up/down control. Switch (audio output only, audio output and servo motor turned on, audio output and servo motor turned off) On/off power switch for entire component. Reachable battery with charging port LED (to show
PROJECT IDEA COMPONENTS 1. Water flow meter 2. Arduino 3. LCD 4. Relay 5. Solenoid Valve 6. Think speak 7. Speaker DESCRIPTION 1. When water flows , the water flow meter should measure the pressure of water in liters and the information about how many liters of water is consumed should be transmitted to think speak 2. For the first four minutes
An Arduino board that produces inputed audio output through a speaker, and power two 9v service motor. Speaker with volume up/down control. on/off power switch. Reachable battery. LED (to show when power is turned on, battery power is full, battery charging, and battery almost dead). USB charging port for Arduino and battery.
I need you to develop some sof...to work in real time. We are taking in the PPG values with an Arduino and connected Pulse Sensor. We have tried connecting Matlab to the Arduino via Simulink with no luck due to inexperience. Don’t care how it’s done. We just need the Matlab algorithm to work in real time with the arduino as it takes in PPG values.
I need you to develop some software for me. I would like this software to be developed using Python. I need someone to create a code for an arduino compatible weather station . This station must send data from a gps module to a mqtt server . I will give more info to anyone who is interested.