Hi. Need to port Microchip ATWINC1500 (ATWINC1510 device, to be exactly) driver for Silabs EFM32 Series 1 microcontroller (EFM32GG11) and their SPI Driver from Simplicity Studio. Not familiar with Atmel Software Framework (ASF), but the library integrated to it.
Control 2 DC motors using IR receiver and remote. Please use MBED compiler.
We are currently developing an electronic driver for PMSM 220VAC Motor. We are using the following HW: _XMC1302 ARM Cortex M0 Microntroller -- mounted on the board INFINEON EVAL-M11302 _IRSM505-065 Power Module -- mounted on the board INFINEON EVAL-M1-05-65D This system (micro board + power board) is driving a 220VAC -- 200 W BRUSHLESS MOTOR. The motor is 8-pole and rated for 12.000 RPM ...
...for the translation table position monitoring system ENEE13020 © Dr Lam Bui 2018 2/4 2. Task Instructions 1. This design must be based on discrete logic circuits. 2. No microcontroller is allowed. 3. Hierarchy design approach must be used. That is the functional blocks of Figure 1 should be implemented using Mutism hierarchical blocks and integrated together
i need a skilled freelancer or agency for a long term job in those field below: Microcontroller programming(Arduino ,Rpi ,STM32 nRF52 PIC ...) Mecatronic,Robotic,embedded system product prototyping then i need someone are equipped by electronics and embedded system tools and hardware for test
...is better to turn ON the LED permanently or after some time. Remember, the switches are press button. I need only the digital design, Not Transistor, NO thyristor, No microcontroller. I am looking for a very simple schematics that can be tested easily on breadboard. The main idea behind this circuit is to design the electronic writing board using
...Hau K., I noticed your profile and would like to offer you my project. We can discuss any details over chat. This is regarding a "Piano silent system" which involved microcontroller with infrared input and sound output with the used of midi chip and other features to build in into the system. I'm thinking it would be nice if we could meet up to talk
Require a freelancer to write a code in C language for Digital Weigh Balance using ADUCM361 Microcontroller. Display on LCD (I2C). Features to be of standard digital balance. keyboard (5 keys), parameter setting, calibration, serial output, option to change parameter setting and calibration through serial communications as well.
Microcontroller 8051 using assembly language which can be run with the KEIL software
Need Programmer For LCD and GLCD interface programming with pic microcontroller in assembly language (ASM) for our educational project. No. of Total Programm: 5 Hardware Schematic Drawing will be provided if needed.
I have current C code that I use to flash atmel micro controller chips and a layout that works but I would like to convert everything to a arduino board (cheaper to acquire these that what I am doing). Basically this I just a program that blinks various LED's at independent rates (i.e. 1 every 4 seconds, another might blink twice every 6 seconds
...develop high quality software and firmware for microcontroller, embedded system and cloud server. - Good knowledge, logical, analytical thinking - Have a system overview and product development mindset - Software language: C/C++, C# - Platform and operating system used: RTOS, Linux, Windows - Microcontroller: ARM core from STM, NXP or TI - Communication
I have Secure Elite 440 meter which has a RS 485 port, and I want to transfer the meter readings using Modbus protocol to a remote server. GSM based microcontroller preferred. Only solution circuit and advise required. NOT ACTUAL HARDWARE. I CAN GET THE HARDWARE PART DONE MYSELF. PREFERRED LOCATION - PUNJAB, DELHI.
...certain level. -The microcontroller should be in standby mode and check the sensor once a minute. -It should keep the last 10 temperature&humidity value in memory. If the average temperature<T1 and average humidity>H1 and battery voltage>V1, it should run the motor at RPM0 until battery voltage is <V0. -Since we will use supercapacitors to power
...framework, that tests all of the io's on our board and communicates with the SIM800 The project must be eclipsed based using the Slober Elipse IDE for the STM32 Microcontroller. You need to use the tasker library, the TinyGSM library and the command parser to receive SMS's and incoming calls to cause an action like toggling an IO. Our board has a SIM800