Structural Engineering Jobs

My project requires the expertise of a civil engineer who has experience with designing and constructing large and complex structures using steel. This project will demand great attention to detail, with a focus on accuracy and quality workmanship. The engineer should have significant experience in structural design, utilizing steel as the primary material. Additionally, experience in site development and transportation engineering means the optimal person for the job will have a range of skills in order to ensure the project is completed successfully and efficiently. Overall, this is a large and complex project, with specifications that require the precision of an experienced civil engineer.

I am looking for some construction drawings to attach to our permit application for a deck expansion for our lake lot. The current structure is in place and well-built and looking to add a section of the deck and complete the roof over the extension. The building restrictions in the area does not allow permanent piles as they are RV recreational sites. SO the only items now being used are the post screw piles you would find at a local hardware store. The existing structure has metal roofing and is 10' 6" wide and is 23' long with roof structure being 30' long approx and a total of 22' 6" wide, as there is 12' on the other side that covers RV. Main structural Posts are 6' x 6' and are 8' centers.

Event center just under 13,000 square feet. Stair case should be CENTERED I also want a loft upstairs for people to sit and relax and an office upstairs 3D rendering is a must

need civil for foundation plan/boq of simple porch 25x20 feet

I am looking for an experienced and knowledgeable freelancer to do a vehicle load analysis on a specific structure using SAP2000. The analysis will consider static loads and is for structural design purposes. I will supply the overall dimensions, material data, vehicle and design code data so that the freelancer can do the appropriate analysis. The final deliverable of this project should be a report explaining the results of the analysis and methods used. Experience with SAP2000 is highly preferred for this project.

I'm looking for a qualified structural engineer to design and drawing a navigation tower of between 30M. The design should adhere to the TIA-222-G standards, and the tower should be able to withstand wind speeds ranging from 162 Kmph. Given the important nature of this tower, the engineer should be Experienced in structural design and well-versed in the applicable engineering principles. I expect the engineer to work closely with me throughout the entire process, providing updates, responding to questions, and making any necessary adjustments that are required. No major surprises should be expected at the end of the project. Thank you for your interest in this job. BASE WIDTH -2.5M TOP WIDTH - 0.75M Exposure - D WIND - 162KMPH HEIGHT-30M 3 LEGGED ANGLE TOWER WITH SEISMIC LOAD PROJEC...

I need the help of a Mechanical or Structural engineer who can help me with stress analysis of a Piping system and Generate Detailed reports using CAESAR II quite urgently, if you have the skills, kindly reach out to me

I am purchasing a steel shop building from my manufacture in China. I am looking to get engineer plans, stamped by a licensed engineer in Ohio for permitting purposes.

I am not skilled in cad but i do much design work. The previous engineer i was working with has been rather disappointing. It has seem to hit a wall and there were some big mistakes. I need to verify some calculations and detail concepts to put on the drawing so i can obtain stamps and seals. Footer Detail CMU Column Detail Wall Section Detail Truss Detail Wood floor framing detail Uplift connector detail Cantilever detail Foundation Plan Truss Plan Floor Framing Plan Roof Framing plan Elevation Views Specs with data and calculations Foundation specs with calculations and factory of safety Truss calculations The structure is 24x56 and i have some cad and revit models. Just need to conclude it. If you have availability i will send you what I have, you can let me know if you can h...

I am in need of a Structural Designer with Precast Experience in USA projects to design parking garages for my upcoming project. The ideal candidate should have experience in designing precast parking garages. Design Codes and Regulations: I will provide specific design codes and regulations to follow for the project. Project Timeline: The project timeline is more than 4 weeks. Skills and Experience: Ideal skills and experience for this job include: - Experience in designing precast parking garages - Knowledge of specific design codes and regulations - Ability to work on a project with a timeline of more than 4 weeks.

I have a blueprints for residential house and need to size the steel beam. Please let me know if you provide this service. If you do, what is cost.

I am looking for a freelancer who can check my SAP2000 model for non linear time history analysis. I have previously conducted this analysis on the model and require software version 2022 for the analysis. The ideal candidate should have expertise in SAP2000 and experience in conducting non linear time history analysis. I am not getting proper hinges in beams and columns for time history hinges in my beam element does not cross IO state for any earthquake hinges are failing in column but the beams are still lying within IO. Specific Requirements: - SAP2000 software version (to be disclosed to the chosen freelancer) - Experience in conducting non linear time history analysis on SAP2000 model

I'm looking to hire a qualified Structural Engineer to design a medium-sized project. The structure I am looking to create could involve residential and commercial projects. Although I may have a rough idea in mind, I am open to new ideas and concepts suggested by the engineer. The engineer should have the necessary experience, have a solid background, and have access to the right resources to complete this project according to my specifications. In addition, the engineer should understand the local and/or state requirements for engineering and be able to provide a permit as needed. This structural engineer will be required to deliver a completed design that meets my needs and provides a cost-effective and safe structure.

New home build on snow zone hillside with upward facing western views of mountain range. ~4000sf. not including garage. pacific nw style. 1 main story with finished daylight basement. 3 bdrm, 3+ bath, great room, den, chefs kitchen, dining, breakfast, office, spa, laundry, mudroom, wine storage room and mechanical/storage room in basement. Fireplace in great rooom and primary bedroom, large deck--partially covered. Would like to maximize mountain views. 3-4 car garage can be in basement. No steps front door/entrance. Prefer a budget friendly design. Floor plan, 3D renderings and CAD file a must.

I am looking for an experienced, certified civil engineer to install a septic tank for a franchise restaurant. The size of the property where the septic tank will be installed is less than 3 acres, and there is no existing septic system that needs to be removed. An estimated number of more than 10 people will be using the septic tank at any given time. The ideal engineer will have a firm understanding of local regulations and building codes, as well as associated safety risks. It is also preferred that the engineer have knowledge of commercial and residential building permit processes.

I need premanufactured building plans reviewed and stamped by an Architectural Engineer

Seeking a LICENSED engineer or architect in Florida who can complete a plan review for an 8'x10' garden shed. Local building code requires wind-load calculations and will require a signed/seal of the drawings. See attached for the drawings I submitted - I will make all changes to your requirements so review work only. Project is final once your sign-off on the drawings is complete. If the bldg dept seeks additional changes, can negotiate an additional project for that work. See attached for the information sent to Bldg Dept. Their response was "The plans submitted for your shed permit need to be signed and sealed by a licensed architect or engineer because of the wind load calculations."

I need the Expertise of A CIvil/Structural Engineer with skills and deep knowledge of working on drainage ..The drainage study should show the existing exit velocity of water prior to construction and exit velocity after construction. A mitigation measure to reduce to the original exit velocity is needed in correspondence to the city codes.

I need an Urgent service of a Structural/Architectural Engineer who can help me quickly work on to get some elevation plans, Truss plans, details, and Load Calculations on my project, i need this urgently, your help would be appreciated, Thanks

I require a Structural engineer to assess an extension so i can continue construction. Need it done asap so more concerned about time frame than cost.

Want to get a FEM analysis on a RC beam created on ABAQUS software using the Concrete Damage Plasticity Model. All the details and required data will be provided. In post-processing, stress-strain graph, representation of failure cracks are the requirements. PFA the image of the model which is to be modeled.

I need an structural engineer license in state of FL that can do calculations and seal the drawing as well. I installed a Gazebo in the backyard, and the city is asking for the poles bases/footer calculation. They want to know the depth of the bases for the poles. Attached is the manual installation from the Gazebo manufacturer, but it doesn't show the depth of the footer.

Mechanical Engineering Structural Analysis Needed Urgently I require a mechanical engineering expert to complete a structural analysis project. The task involves analyzing the structural integrity of a mechanical component. The project is urgent and needs to be completed within three days. Ideal Skills and Experience: - Strong background in mechanical engineering - Expertise in structural analysis - Familiarity with CAD software - Ability to meet tight deadlines Please provide samples of previous work in the field of mechanical engineering.

I am looking for a freelancer who can review the structural drawings for my duplex house in Vancouver, BC Canada. The house is between 2,000-3,000 square feet. I will provide specific local building codes and regulations that should be considered. The ideal candidate should have experience in load-bearing analysis and be familiar with the local building codes and regulations.

I am in the permitting and approvals phase of my project and seeking a structural engineer to assist me. My deck sunrooms and garages are already designed and I have provided the dimensions and location of the structures. I am looking to use wood as the primary structural material. Ideal skills and experience for the job include: - Expertise in wood structural design and analysis - Knowledge of local building codes and permitting requirements - Experience with deck sunrooms and garage construction - Ability to provide detailed structural drawings and calculations - Strong communication skills to work with myself and other contractors involved in the project

I m buying inground pool kit. I need plan stamped and signed for town permit.

I am not skilled in cad but i do much design work. The previous engineer i was working with has been rather disappointing. It has seem to hit a wall and there were some big mistakes. I need to verify some calculations and detail concepts to put on the drawing so i can obtain stamps and seals. Footer Detail CMU Column Detail Wall Section Detail Truss Detail Wood floor framing detail Uplift connector detail Cantilever detail Foundation Plan Truss Plan Floor Framing Plan Roof Framing plan Elevation Views Specs with data and calculations Foundation specs with calculations and factory of safety Truss calculations The structure is 24x56 and i have some cad and revit models. Just need to conclude it. If you have availability i will send you what I have, you can let me know if you can h...

Small residential addition that is 12x16 feet

I am looking for a skilled professional to help me build an auxiliary dwelling unit on my property in Silver Spring. This project and other I work on requires 1) Mechanical engineering consultants, and 2) Electrical Engineering consultants. I am seeking someone who can work efficiently to meet my timeline of less than 6 months for this and many other projects (Hopefully12-22 per year). I need a reasonable rough estimate to sign contracts and final estimate at construction documents. Key details about the project include: - The property is 600 square feet in size with a$150k budget. - A new structure will need to be built for the auxiliary dwelling unit. - I am open to advice and suggestions on how to best approach the project. - This is more of a budget project than custom design. Idea...

About the Job Azierta (), a European civil engineering consultancy firm with headquarters in Madrid, Spain acting in the US through Azierta LLC, based in the Washington DC metro area. We are looking for a Professional Engineer (PE) licensed in Virginia who specialized in Naval and Marine Engineering, interested in establishing a part-time, per-contract relationship in which most of the work will be done remotely. This relationship will benefit from our investment capability, long track record (over 1,000 projects executed successfully), solid background in key technologies, and strong ties to large European construction companies leading large contracts in the US. QUALIFICATIONS: Required: • Bachelor´s Degree in Engineering from an accredited institution. • Active Professi...

Residential renovation needing structural expert for council consenting works. Location must be in Wellington, New Zealand.

Residential renovation needing structural expert for council consenting works. Location must be in Wellington, New Zealand.

Have a rough 3d design on Sketchup. Need a 2d building layout and structural engineering for the floor and roofing systems. Basics: 24'x40' layout with full ICF Basebment 9x15' bump out for entry mud room and basement stairs 12x15' Screened in porch attached Attached are pdf views. WIll provide full 3d layout.

I am seeking a professional civil highway engineer to complete the design for my highway project. The scope of the project is design only. The timeline is flexible, Ideal skills and experience: - Civil engineering degree or related field - Experience in highway design and planning - Knowledge of relevant regulations and standards - Proficiency in CAD software - Strong communication and project management skills.

The Project needs a Structure Design and Drawing to begin with. The area of the site is 28mx20m. We need a structural engineer who can create Drawings/ blueprints and suggest best quality material to use under given budget for best durability. More information will be provided once selected.

I want to build a custom structure design on my residence rooftop. I have rendering designs. I need architectural drawings to submit to the city building department. Constructiondrawing preparation, wind uplift calculations, electrical engineering calculations, electrical light photometry, plumbing isometrics and shop drawings for all custom millwork. Preparation and submission of forms and drawings required for all necessary approvals, including building permits, zoning approval.

Power plant construction in Termez, Uzbek. We are looking for Engineers that can speak and write in English.