Closed

1 ADC input to 5 DAC outputs

Hi,

I need software (in C, Simulink, ... anything that goes & is changeable afterwards) to flash on an embedded system (which I haven't purchased/designed yet).

I know a lot of the basics but I'm still a student in electrical engineering.

The system gets 1 analog input to turn the system on or off (it's 12 V) and 1 analog input (varying between 2 - 5 V).

When the system's on it has to output 5 different signals continuously:

4 analog signals and 1 digital signal with a constant duty cycle (it may have an amplitude of 5 V, but 12-13 V would be better).

3 out of the 4 analog signals vary between 0 - 5 V.

The other analog signal is a bit more complex, it has to be the signal of a crankshaft VR sensor (with 60 -2 teeth). It has an amplitude varying between -5 and 5 V, up to -12 to 12 V. It's frequency range varies between about 650-700 Hz up to 4 to 4,5 kHz.

The output signals differ in frequency or value, depending on the given input signal.

I think it would be easiest (and less epensive) if I purchase an already-made PCB with components instead of designing a new one.

The board will be supplied with 12 VDC , but of course it's also possible to supply it with 5 VDC.

If this concept works properly I will make more boards quite similar to this one, but with 7 output signals and the others a bit modified. So it would be best to preserve those extra signals already on my board/microcontroller and I'm also looking for software that's adjustable for me (in terms of delays for the outputs to change and to adjust to output signals).

I also have images and scope data for the input/output signals.

Thank you very much in advance,

F.V.

Skills: C Programming, Embedded Software, Microcontroller, PCB Layout, Software Architecture

See more: the basics of programming, system sensor, student programming board, scope programming, programming basics, need an engineering student, gets in c programming, digital designing, c# programming scope, c programming input output, c programming basics, bit frequency, best designing software, basics of c programming, best microcontroller, VR, need electrical engineering student, microcontroller analog, hz, embedded system designing, digital concept, dac, basics of programming, Architecture designing, adc

About the Employer:
( 0 reviews ) Belgium

Project ID: #5159698

16 freelancers are bidding on average €345 for this job

MikroStar

hi, i am an electrical engineer. i have expertise in embedded system design.i can help you with this project.

€1200 EUR in 40 days
(22 Reviews)
6.3
nicu66pr

Hi, I am not sure if my understanding is clear but I can provide the behaviour you want using a DAQ system and Labview to create a control program on your computer. I think a USB DAQ device which costs about 150 eu More

€250 EUR in 10 days
(3 Reviews)
3.9
DamithaKD

HI, About ME : I am a programmer for 8 years and has perfect reviews on all my projects.I am a Expert in Delphi and Scjp, I have a Diploma in Electronics and a EEE (3rd year) student in NITW, india. i have expe More

€222 EUR in 3 days
(24 Reviews)
5.3
AliMushtaq12

Hi! I am an Electrical Engineer with expertise in embedded systems. I have done a lot of projects on different micro-controllers in the industry like PIC and Arduino. I can do the job for you. Waiting for your respo More

€220 EUR in 7 days
(3 Reviews)
3.5
akramkarimi1036

WOW! It seems that this project was posted by me... As I can program wide variety of controllers including low end (8051,PIC,AVR,MSP430) and high end ARM Cortex-M core based (STM8,STM32,Kinetis controllers by Freescale More

€200 EUR in 10 days
(2 Reviews)
3.0
shahbaz1980

Hi, i have already developed similar projects and sent to USA, you will require different oscillators with variable frequencies. i have 2 options to go for this. 1) using filters with microcontroller and converting sq More

€388 EUR in 30 days
(5 Reviews)
3.8
GlobalElectronic

A proposal has not yet been provided

€1111 EUR in 15 days
(11 Reviews)
4.3
betaenergy

Dear Sir, We are Reserach and Development company whose working area are : -Digital Motor Control -Analog Design -Electronic Design -Power Electronics -PCB design -Embedded system -Matlab -Simulation of ha More

€244 EUR in 3 days
(13 Reviews)
4.7
hpvinayaka

Hello, I have 13+ years of experience in embedded systems hardware and firmware development. I am interested to work on your project. Thanks.

€250 EUR in 15 days
(0 Reviews)
0.0
skrynha

Hi, I read you requirements. Because I have been working last years on similar project with ADC, DAC, PWMs, I would recommend you to first choose your hardware, because the code will be strongly dependent on hardwa More

€444 EUR in 20 days
(0 Reviews)
0.0
eshanic

Hi, I am interested in this assignment and have 10 yrs of experience in Embedded Systems. Please let me know the project details like which microcontroller n where is the o/p connected then I can help you out. You c More

€222 EUR in 10 days
(0 Reviews)
0.0
ahsenj

Sir, I am an Electrical Engineer with vast experience of Electronic Circuits and Schematics. I have a complete graps of Micro-controller Programming in C language and am proficient inSimulink as well. So I can comple More

€244 EUR in 5 days
(0 Reviews)
0.0
OctarineBelgium

Vertel es net iets meer over wat je exact wil. Dit is echt wel meer dan ADC naar DAC want een typische ADC/DAC werkt op pakweg 2 tot 5V. Je hebt dus wat elektronica nodig om +-12V om te turnen naar bv een 0-2V signaal More

€155 EUR in 3 days
(0 Reviews)
0.0
christog

Hi. We're a team of developers. I can get your work done in the prescribed time. I have top-notch developers at my [url removed, login to view] you chat with me 2 mins i'll provide a solid solution for you. waiting for your replay.

€250 EUR in 4 days
(3 Reviews)
0.0
pmullappilly

Hi, I am a graduate in EEE.I have 15 years of experience in programming,electronic design and teaching.I can do this work for you. It can be easily implemented using SPIC33FJ64GP804T-I/PTTR-ND .I will design the ha More

€111 EUR in 10 days
(0 Reviews)
0.0
GabrielSoare

Hello there. I can do your job at a good price and a decent time. I am an electronic engineer and also the owner of this site : [url removed, login to view] where in Code Samples section you can see my free available work. I can do More

€230 EUR in 14 days
(0 Reviews)
0.0
mohamedmaged92

-i will send you a free sample -you can ask me any additional modifications within 3 days after receiving the full job -you can ask for any type of PCB design (single layer or double layer ) and having the desig More

€34 EUR in 3 days
(0 Reviews)
0.0
diegosalazar

Expert in microcontroller. PCB in Proteus All the protorype , send will a video in youtube. Ready for begin DIego

€222 EUR in 12 days
(1 Review)
2.1
ancitiousManish

hi! I have more than 4 years of experience in embedded firmware development. I can provide you solution on 8051, pic or arm based processor. thanks & regards, Manish

€233 EUR in 20 days
(0 Reviews)
0.0
cosminpop83

Hello, I have already most of the parts needed for your project, so i think it will go pretty fast. There are some things that don't match in your description, but this will be solved. So, because i do this everyda More

€250 EUR in 30 days
(0 Reviews)
0.0