Closed

Design pcb in easyeda using ESP32 Development Board controller, and Setup the project ready to order shipping. programming in Arduino Program. program sensors, print real data obtained on screen and arduino monitor.

Hydroponics system, Design pcb in easyeda using the ESP32 Development Board controller, and Configure the project ready to order shipping. programming in Arduino Program. program sensors, print real data obtained on screen and arduino monitor.

ABOUT THE PROJECT:

-The PCB board must be a support plate for mounting external modules or with additional outputs, components such as resistors, capacitors, connectors, modules, etc. They must be components of the most Universal possible. The objective is to make the project more efficient and thus avoiding cables.

The total measurement of the pcb card must have a maximum size without exceeding the measurements 9x15cm.

-The screen has a simple menu that displays the data sensed in real time and uses the encoder to modify parameters such as the time, color of the rgb led strip, humidity level required to turn the pump on or off.

-110v power source with 12v output and 15 amp power

Below are the sensors to include:

1) ESP32

2) ZMPT101B

3)ACS712 30A

4) HYGROMETER MODULE X2

5) DHT11 TO INTEGRATE EXTERNALLY

6) bme280 sensor module TO INTEGRATE INSIDE THE MOTHERBOARD

7) L298N MOTOR CONTROLLER

8) RTC MODULE DS3231

9) KY-040 ENCODER

10) RGB LED STRIP

11) LDR SENSOR MODULE WITH CONNECTION TO EXTERNAL SENSOR THROUGH CONNECTOR

12) MICRO SD READER

Next I will attach some photos examples of my progress of the developed project. So you can get an idea of ​​what I'm looking for.

previously I have developed a pcb with this concept I will be sharing it in photos to copy this same concept.

Skills: Arduino, PCB Layout, Electronics, Microcontroller, Electrical Engineering

About the Employer:
( 0 reviews ) Toronto, Canada

Project ID: #32656945

33 freelancers are bidding on average $243 for this job

avigupta0061

Best Esp32 Design Expert at your doorstep! Dear Client, We can design PCB using EasyEDA based on Arduino and set up and develop the Hydroponics System while meeting all requirements for you. We have seen the all atta More

$250 CAD in 2 days
(51 Reviews)
7.6
(186 Reviews)
7.2
(99 Reviews)
6.6
(114 Reviews)
7.0
kingch91

Hi, With an experience of more than 7 years as an embedded software engineer, PCB designer and product lead, I can provide you with end-to-end IoT/embedded solution starting from your idea to its actualization and deve More

$200 CAD in 7 days
(152 Reviews)
6.6
(31 Reviews)
6.5
macroenergy

Thanks for Freelancer which gives chance to meet you. I hope you are good. I have read your description carefully and understand everything. I’m Electronics engineer who have 25 year experience on analog design, renew More

$84 CAD in 7 days
(59 Reviews)
6.5
Devpro11

Hello there. I hope to work with you because your project is very familiar to my past works. [login to view URL] I have 9+ years of experience in Electrica More

$180 CAD in 3 days
(31 Reviews)
5.8
engrhassanwali

Hi! I have understood your requirnments about your project with every detail of it. I am an Electrical Engineer with more then 9 years experience in electronics, circuit design, PCB layout, Verilog, FPGA, Embadded Syst More

$250 CAD in 7 days
(22 Reviews)
5.6
etalhak

Hallo, I am an electronics and telecommunication engineer and my major is wireless systems' design. I am experienced in hardware and embedded systems' design. So far I have designed/printed/tested many PCBs and I am qu More

$140 CAD in 7 days
(47 Reviews)
5.5
HarimohanG

Hi, i can design PCB based on Arduino with using ESP32/Board controller on EasyEDA platform and while meeting all requirements for you. I have seen the attached documents you shared. I have humungous experience in Ard More

$140 CAD in 2 days
(4 Reviews)
5.2
(27 Reviews)
5.1
Valuesolutions

Hello, I hope this finds you well. I have just seen your project requiring; Electronics Microcontroller Electrical Engineering PCB Layout Arduino I believe that my 10-year experience in this field is what you need rig More

$250 CAD in 7 days
(20 Reviews)
5.4
soltracker

A very simple and easy project to be done..Its me imad a hi tech pcb designer.........thanks for posting the job........................................................

$60 CAD in 4 days
(85 Reviews)
5.0
VTElectronics

Hello Sir I'm an Electronic Engineer with over 6 years experience developing embedded applications and PCBs, you can learn more about me from my website at [login to view URL] How about a private message More

$250 CAD in 7 days
(19 Reviews)
5.1
Nazir63

Hello, I have come from Electrical and Electronics Engineering background. My passion is programming and Robotics. Currently I am working as a Mobile and Web Developer at a local IT company . In academic life I have wo More

$100 CAD in 2 days
(40 Reviews)
4.9
Safeer143

Hello. We are a company of mechatronics, electrical, computer and software engineers with vast expertise in PCB layout, embedded systems, AC/DC converters, stepper motors, transformers, machine learning, raspberry pi, More

$300 CAD in 7 days
(16 Reviews)
5.1
lavervalik

Hello. I am an Electrical/Electronics Engineer. I am expert in hardware and software developement field. My skills are - Professional PCB design(ALTIUM Designer, KICAD, EAGLE) - Arduino/ Microcontroller(Arduino IDE, Pl More

$210 CAD in 3 days
(5 Reviews)
4.4
kostyausha

Hello. I hope to work with you on your project as I am very familiar with my past work. I have over 10 years of experience in electrical engineering and PCB layout and circuit design and an electronics engineer and ex More

$250 CAD in 7 days
(6 Reviews)
4.1
Lilywang70

[login to view URL] you for your job posting. I have been working as a firmware and hardware designer for 8+ years. I had developed several similar projects using the various microcontrollers such as STM32F1/2/3/4/7xx, PIC16/1 More

$250 CAD in 3 days
(5 Reviews)
4.2