Closed

Pressure sensor transducer code

Hi people,

I have px302-050av pressure transducer

4 wires want to connect to UNO using the Arduino program. I had connected the pump to the same UNO and wrote the code for the pump and it’s working good. But I want to connect the sensor to get signal and code it. My project is to control the liquid level. I want the sensor to send signals to the UNO to run the pump on/off depending on the level I choose.

Link for the pump I am using:

https://www.amazon.com/Peristaltic-Metering-Stepper-Motor-0-88mL/dp/B01LY35CKH/ref=sr_1_1_sspa?ie=UTF8&qid=1520975396&sr=8-1-spons&keywords=Peristaltic+Metering+Pump+with+Stepper+Motor+1.0A+0-88mL%2Fmin&psc=1https://www.amazon.com/Peristaltic-Metering-Stepper-Motor-0-88mL/dp/B01LY35CKH/ref=sr_1_1_sspa?ie=UTF8&qid=1520975396&sr=8-1-spons&keywords=Peristaltic+Metering+Pump+with+Stepper+Motor+1.0A+0-88mL%2Fmin&psc=1

Link for the sensor:

[login to view URL]

The UNO:

HiLetgo UNO R3 ATmega328P CH340 Development Board Compatible Arduino UNO R3 Arduino IDE Develope Kit Microcontroller with USB Cable Straight Pin Heade [login to view URL]

The code for running the pump:

int PUL=7; //define Pulse pin

int DIR=6; //define Direction pin

int ENA=5; //define Enable Pin

void setup() {

pinMode (PUL, OUTPUT);

pinMode (DIR, OUTPUT);

pinMode (ENA, OUTPUT);

}

void loop() {

for (int i=0; i<6400; i++) //Forward 5000 steps

{

digitalWrite(DIR,LOW);

digitalWrite(ENA,HIGH);

digitalWrite(PUL,HIGH);

delayMicroseconds(50);

digitalWrite(PUL,LOW);

delayMicroseconds(50);

}

I need code for both of the parts that’s make the sensor send signals at specific level of liquid to the pump to off and on.

Also, need how connect the sensor to the UNO

Skills: Arduino

See more: water pressure sensor, barometric pressure sensor, non intrusive pressure sensor, non intrusive water pressure sensor, pressure sensor led circuit, code embed compatible android, energy aware routing wireless sensor network code matlab, acoustic vector sensor matlab code, code jquery compatible, compensation pressure temperature pic code, gyro sensor iphone code, php code mobile compatible site, set homepage code firefox compatible, convert vb6 code mac compatible

About the Employer:
( 0 reviews ) United States

Project ID: #16781442

21 freelancers are bidding on average $154 for this job

mechatronicsengr

Hi, I hope you are doing well. I have expertise in embedded system programming and development. I have reviewed your project details and I am confident to implement your required algo in less possible time. Looki More

$200 USD in 3 days
(41 Reviews)
6.1
ircrashed

Hello I have got your job posting “Pressure sensor transducer code” and I am very much interested to work in your project. I am a circuit designer and have more than 5 years experience of working with the Analog More

$150 USD in 3 days
(29 Reviews)
5.1
urbito

Hello there! Hope you doing good! If you still need this to be done, be sure to contact me. Lets make something awesome! Greetings!

$250 USD in 28 days
(24 Reviews)
4.5
xaainulabideen

A proposal has not yet been provided

$200 USD in 3 days
(18 Reviews)
4.8
rishiajmera

Hello, Greetings! With a proven track record of successful achievements, I am pleased to present my application for your consideration as a Freelancer. Please have a look at my profile and portfolio to get an idea a More

$155 USD in 3 days
(6 Reviews)
3.9
xiaoguang2018

Hello. If the px302 is a 4-wire type, it would be better to apply 10v as the standard for the voltage (red, black). And since the outlet is 10mv / v, it is better to add an amplification circuit to widen the measurem More

$155 USD in 3 days
(9 Reviews)
3.8
chanchalkks

Hello, I understood your requirements that you mentioned in Job Post. Can you please send me the datasheet of sensor (As in the link that you have attached not provide me the datasheet). I will provide you the com More

$222 USD in 7 days
(13 Reviews)
3.5
$244 USD in 3 days
(3 Reviews)
3.1
farhatshahir

Question is, there is a lot of freelancer for this job Sir, why me? Dear Sir, My daily routine is writing code from morning to midnight. This is my life. And I love especially the Arduino. Isn't it fun? You write c More

$150 USD in 5 days
(4 Reviews)
2.9
ahmedradwan94

I'm expert in Arduino programming as I've done many projects with it before. you can see that in my portfolio. Guaranteed delivery on time with the best quality.

$166 USD in 3 days
(2 Reviews)
2.4
kishorravi

I have experience in similar modules I have uno with me. if you can arrange the sample sensor I can test the code in my desktop and deliver the driver fault freee

$111 USD in 7 days
(0 Reviews)
0.0
teknoteam

Hi, the sensor you're using requires signal conditioning, this means some extra electronic components to be added and tested. If you like I can suggest some different sensor that are best fit for the purposes and t More

$205 USD in 7 days
(0 Reviews)
0.0
chen4567

I have experience with sensors, actuators, and Arduino. My background is feedback/closed-loop control. Your project is in my alley. Note: your pressure sensor might not have the accuracy to measure liquid level. Accord More

$155 USD in 3 days
(1 Review)
0.1
$155 USD in 3 days
(0 Reviews)
0.0
$66 USD in 3 days
(0 Reviews)
0.0
cnwaithira

Having understood the job in question, i am in a position to handle it. I have an excellent command in arduino, having worked with it for quite sometime. I intend to complete the job within the required timelines, as i More

$105 USD in 3 days
(0 Reviews)
0.0
inspiredwhiz

It’s a privilege to know that you are going through my proposal. However, I would like if you can spend a little more time and check my portfolio as well. That’s how you can see what I can do for you as well as my serv More

$30 USD in 1 day
(0 Reviews)
0.0
$155 USD in 4 days
(0 Reviews)
0.0
khanicha

Hello, You simply read the sensor by using digitalRead() function in case your sensor plugged in digital pins, otherwise using analogRead(). So then, using a formula or conditional if/then filter, you could combine More

$150 USD in 3 days
(0 Reviews)
0.0
cheetahpixie

Are you using analog inputs? Does the pump support variable input? A lot of things to consider here. Though, if we read the documentation and apply the methods, I imagine this should be easy as cake.

$155 USD in 3 days
(0 Reviews)
0.0