Closed

Assembly developer needed

Using the STM32F4-Discovery Board, you are to design a Programmable Function Generator

(PFG) capable of producing two different electrical signal waveforms at seven different signal

frequencies. The PFG is to meet the following requirements.

1. Two different waveforms are to be generated, as selected by the user.

a. “Sawtooth” – the signal is to rise linearly from 0 volts to 3 volts during each time

period of length T.

(This should be the default waveform after the system is reset.)

b. “Triangle” – the signal is to rise linearly from 0 volts to 3 volts in the first half of

each period, and then decrease linearly from 3 volts to 0 volts in the second half

of each period, where the total period length is T.

2. Each period of the waveform is to comprise 100 data points, spaced evenly across the

period. The data are to be 12-bit unsigned numbers, ranging from 0 to 4095. These

correspond to output voltages from 0v to 3v, respectively.

3. There is to be an “off” condition (no generated waveform) plus seven user-selectable

waveform periods: [OFF, 0.5s, 1.0s, 1.5s, 2.0s, 2.5s, 3.0s, 3.5s]. These periods must be

accurate to the nearest microsecond (thus requiring the use of a programmable timer.)

4. All timing is to be produced by periodic interrupts from Timer 6 on the microcontroller.

5. The waveform period and type are to be selected with the User Button on the board as

follows.

a. The PFG is to initially be off (no waveform generated).

b. Each push of the button selects the next period in the list:

[OFF, 0.5s, 1.0s, 1.5s, 2.0s, 2.5s, 3.0s, 3.5s]

c. Allow time for the period to be examined before pressing the button again.

d. However - if the button is pressed twice within a 2-second interval, the

waveform type is to be changed to the other format (Sawtooth to Triangle, or

vice-versa).

6. The User Button is to trigger an interrupt each time it is pressed – all responses to the

User Button should be done by an interrupt handler. The User Button should be

“debounced”, as necessary, to prevent more than one action per button press.

7. The blue LED is to blink at the rate of the selected waveform period.

8. LEDs 4-3-5 (green-orange-red) are to display a 3-bit binary number (0 to 7), indicating

which of the 8 waveform periods (OFF through 3.5s) is currently selected.

9. The digital data values of the waveform would normally be converted to analog voltages

by the microcontroller’s digital-to-analog converter (DAC). Since you will not likely have

an oscilloscope to display the waveforms, write the data values to a global variable

named “DACvalue”, and display that value in the “Logic Analyzer” window of the Keil

debugger. This will show the generated waveform, including both magnitude and

frequency.

Skills: Assembly

See more: assembly programmer, assembler language jobs, assembly developer salary, jobs for assembly language programmer, assembly language jobs salary, assembly language programmer, assembly language jobs reddit, qbfc freelance developer needed, iphone developer needed, outsource developer needed, cakephp developer needed, php oscommerce developer needed, ajax developer needed, assembly code 8086 using 8051, flash games developer needed, delphi developer needed, magento website developer needed, mmorpg developer needed, aspnet developer needed, joomla developer needed

About the Employer:
( 0 reviews ) Auburn, United States

Project ID: #26761951

1 freelancer is bidding on average $389 for this job

milindlicade

I have been working in the embedded field for last 6 years working on different boards with exposure to c, c++, python and also I have knowledge of the assembly programming and also have work experience to related it.

$389 USD in 15 days
(0 Reviews)
0.0