Needs a PCB design expert

Closed Posted 3 months ago Paid on delivery
Closed Paid on delivery

Using PIC18F4580, I want to write a program that do the following :

- When the switch is on there is an output LED 1 Light that represents the device is started ( run) ,like any simple device.

- Mainly the device check continuously if another switch (special switch) is triggered ,DC buzzer and LED 2 light is running as alarm

- Lastly, there is PUSH BOTTON 2 that switched on to senses any motion using motion sensor PIR. After that, the device outputs the same DC buzzer and LED 2 Light as alarm, and will be switched OFF if the user pressed PUSH BOTTON 2, so the user make sure the device doesn’t detect him as false detection

Note that:

1- This device is Electronic Fishing Bite & Security Alarm, just to clarify this project requirements

2- I want to use C language using Mplab , and I need use Proteus to simulate the device circuit.

Electronics Microcontroller PCB Layout Electrical Engineering Arduino

Project ID: #36705008

About the project

17 proposals Remote project Active 2 mos ago

17 freelancers are bidding on average $25 for this job

kingch91

Greetings, I have read and understood your requirements, you need someone expert in PCB designing. I am an electronics engineer and expert in PCB design tools and multilayer PCB designing with 3d step files using KiCa More

$20 USD in 1 day
(180 Reviews)
6.9
anahhal

Hi there, and I'm excited to learn more about your needs for a PCB design expert. Using PIC18F4580, I understand you want to write a program that do your needs.

$100 USD in 3 days
(23 Reviews)
5.8
Adeel2k14

I am Muhammad Adeel, an experienced electrical engineer with expertise in designing electronic circuits and PCB boards. I have vast experience in solving electrical problems and have designed various electronic circuit More

$20 USD in 7 days
(47 Reviews)
5.8
tokumei

Hi,  Good day! This is Lawrence, a hardware design engineer, and I'm interested in working on your project. I've been designing circuits and PCBs for many years and would like to assist you. Please contact me anytime More

$15 USD in 10 days
(8 Reviews)
5.6
Sherry1596

Hello, my name is Shehryar and I am an experienced electrical engineer with 7+ years of experience in electrical engineering. I specialize in electronics engineering, product engineering, SoC/SBC/USB/HDMI/Ethernet desi More

$20 USD in 7 days
(7 Reviews)
3.9
shnmgh

I have more than 6 years’ experience at experience in embedded hardware designing, multilayer PCB layout with “Altium designer” and “KiCad”. My specialty lies on ARM Based embedded system design with EMC standard. I ha More

$10 USD in 7 days
(5 Reviews)
2.1
jayanthd2k12

I have 10+ years of experience in electronics and especially embedded electronics. I have worked with 8051, PIC10/12/16/18, dsPIC, PIC24, PIC32, STM8/32, Arduino, Raspberry Pi, ESP32, FT90x microcontroller or modules. More

$30 USD in 2 days
(2 Reviews)
1.6
ProNandan5

Hi, I Can help in the last stage of simulation using proteus software. After getting the circuit diagram and hex file of the ready program I can provide you with the simulation.

$10 USD in 7 days
(0 Reviews)
0.0
ahmedmubarik

Dear Client. I have read your " " requirement and I am 100% confident that I can complete your project perfectly. My best skills are PCB design and schematic design using Altium, KiCad, Eagle, Proteus. Here is my past More

$30 USD in 7 days
(0 Reviews)
0.0
kktroops90

Have more than 10 years of Experience in Electronics Product Development, Developed High-Quality Electronics Products. Developed below Products: 1. FPGA & Verilog Code based Boards: Video Processing Board Signal Proc More

$25 USD in 7 days
(0 Reviews)
0.0
Himanshu582005

I am studying the electrical and electronics engineering in BTech. I have made many small - small project in my college same as like your requirements.

$25 USD in 3 days
(0 Reviews)
0.0
modihardik2881

I am very interested in working on the project! My experience in PCB design and embedded systems can bring great ideas to your project! I have extensive experience in PCB design. In addition, my proposal includes the m More

$20 USD in 7 days
(0 Reviews)
0.0