SEPIC Converter Design 12V/2A

I need a SEPIC converter with the following characteristics

Vin(min) = 11V

Vin(max) = 30V

Vout = 12V

Iout (max) = 2A

f = 100khz - 300khz

found design with LT3759 chip ANALOG DEVICES [login to view URL] i dont know if its an high cost design or not and good quality or no too and Analog devices parts are now not used very much in professional design ?

and other think i see some board use regulator like LM2678, LM2596 .... maybe we should ensure that the input voltage is higher than the output but if the input was 12.8v and ouput was 11v its not a problem i can get my 3.3v and 5v from this output ...

Thank you in advance.

Skills: Electronics, Electrical Engineering, PCB Layout, Microcontroller, Circuit Design

See more: boost converter design pspice, buck boost converter design pspice, boost converter design simulation, buck boost converter design, voltage converter laptop 12v 19v, boost converter design review, voltage converter circuit 12v 19v, circuit design 12v 19v converter, dc dc converter schematic 12v 19v, graphic design joborders outsourced abroad cutting cost purpose, bidirectional converter design, converter design using microcontroller wind turbine, youtube converter design, project sepic converter, buck converter design multisim, buck converter design, pic controller based sepic converter, catalytic converter design working animation, power supply design 12v design

About the Employer:
( 3 reviews ) bois d'arcy, France

Project ID: #28978358

Awarded to:

(3 Reviews)

12 freelancers are bidding on average €37 for this job


Best SEPIC Design Expert at your doorstep! Dear Client, We can provide you SEPIC converter with the mention characteristics We couldn’t stop ourselves from bidding after going through the description as they are an ex More

€100 EUR in 2 days
(19 Reviews)

Hi. I have good experience in power converter design such as boost, buck converter. I have read your project description, so I am very confident in your project. I will finish your board design in a short time perfectl More

€30 EUR in 1 day
(23 Reviews)
(37 Reviews)

Dear Client, I can design SEPIC Converter 12V/2A as per your requirements. I have read and understood your requirements and could do it for you in the least time and utmost superior quality. I have experience in Boost More

€50 EUR in 2 days
(3 Reviews)

Hi Sir I am student of MSc Mechatronics and Control Engineering. I have done BSc Electrical Egineering. I am very expert in PCB designing and circuit design. I read your description carefully. I can do it. I can also s More

€50 EUR in 4 days
(26 Reviews)

Hi I am an expert with more then 6years of experience in IoT, Automation, Embedded Systems, pcb design and dovelopment and prototyping. I have hands-on experience in arduino, esp32, pic, arm, raspberry pi and other mcu More

€24 EUR in 3 days
(15 Reviews)

I am Engineering with specialization in PCB Layout Designing, I have 4 years of industry experience working altium design tool, I have worked with various project-related altium also I have knowledge of programming als More

€30 EUR in 1 day
(4 Reviews)

I am designing DIY projects and real time automation projects, specialized in DC-DC power converters, automation circuits and microcontroller projects. I have been contributing articles to Electronics For You magazine More

€30 EUR in 3 days
(4 Reviews)

I'm electronic system engineer with master in automation control in power electronics and I can do this project for you. It's not clear to me if you want a project with the LT3759 or other chips may satisfy your needs More

€30 EUR in 2 days
(1 Review)

Hello. My name is Mehmet. I’m able to help you. I have been working as a hardware specialist. Thank you.

€29 EUR in 5 days
(0 Reviews)

Greetings, Good day! I have good experience in PCB layout design and worked in the boards like RIGID FLEX,HDI,RF and power boards till the end of gerber genaration with good output as per client requriment and need.T More

€22 EUR in 5 days
(0 Reviews)