Serial Comm Standard C Library & Windows DLL

Serial Comm Standard C Library & MS Windows DLL 1) Be able to compile & build the Serial Comm Standard C Library in Target platforms Linux/Unix/MS Windows 2)Standard C Library & Windows DLL must follow the following: a)Thread Safe. b)Source code must be provided. c)Development Environment Microsoft Visual Studio 6 must support for Standard C Library & Windows DLL. d)Makefile for Linux/Unix must be provided. e)Support for RTS/CTS and DSR/DTR hardware handshaking, and XON/XOFF software flow control. f)Basic Functions: 1) Open_Port 2) Write_Port 3) Receive_Port 4) Close_Port e)Restores FIFO state properly when port is closed. f)Support port controls. 1) Baud rates to 115,200 2) Odd, Even, No parity. 3) 5, 6, 7, or 8 data bits 4) 1, 1 1/2, or 2 stop bits 5) XON/XOFF software flow control 6) RTS/CTS, and DSR/DTR handshaking g) The number of ports is dependent upon hardware only. h) Being able to: 1)Read a character, string, block 2)Read a string 3)Read a block 4)Write a character 5)Write a string 6)Write a block 7)Set or clear DTR, RTS 8)Enable / disable XON/XOFF software flow control handshaking 9)Enable / disable RTS/CTS handshaking 10)Send Break Signal 11)Calculate 16- or 32-bit CRC 12)Clear line errors 13)Get all line status bits 14) Is Rx buffer empty? Full? 15) Is Tx buffer empty? Full? 16) Clear Rx buffer, Tx buffer 17) port status 18) Has Break Signal been received? 19) Receiver overrun occurred? 20) Parity error occurred? 21) Framing error occurred? 22) Error Message Return error code’s ASCII name ## Deliverables 1) Complete and fully-functional working program(s) in executable form as well as complete source code of all work done. Serial Comm Standard C Library & MS Windows DLL 1) Be able to compile & build the Serial Comm Standard C Library in Target platforms Linux/Unix/MS Windows 2)Standard C Library & Windows DLL must follow the following: a)Thread Safe. b)Source code must be provided. c)Development Environment Microsoft Visual Studio 6 must support for Standard C Library & Windows DLL. d)Makefile for Linux/Unix must be provided. e)Support for RTS/CTS and DSR/DTR hardware handshaking, and XON/XOFF software flow control. f)Basic Functions: 1) Open_Port 2) Write_Port 3) Receive_Port 4) Close_Port e)Restores FIFO state properly when port is closed. f)Support port controls. 1) Baud rates to 115,200 2) Odd, Even, No parity. 3) 5, 6, 7, or 8 data bits 4) 1, 1 1/2, or 2 stop bits 5) XON/XOFF software flow control 6) RTS/CTS, and DSR/DTR handshaking g) The number of ports is dependent upon hardware only. h) Being able to: 1)Read a character, string, block 2)Read a string 3)Read a block 4)Write a character 5)Write a string 6)Write a block 7)Set or clear DTR, RTS 8)Enable / disable XON/XOFF software flow control handshaking 9)Enable / disable RTS/CTS handshaking 10)Send Break Signal 11)Calculate 16- or 32-bit CRC 12)Clear line errors 13)Get all line status bits 14) Is Rx buffer empty? Full? 15) Is Tx buffer empty? Full? 16) Clear Rx buffer, Tx buffer 17) port status 18) Has Break Signal been received? 19) Receiver overrun occurred? 20) Parity error occurred? 21) Framing error occurred? 22) Error Message Return error code’s ASCII name 2) Installation package that will install the software (in ready-to-run condition) on the platform(s) specified in this bid request. Serial Comm Standard C Library & MS Windows DLL 1) Be able to compile & build the Serial Comm Standard C Library in Target platforms Linux/Unix/MS Windows 2)Standard C Library & Windows DLL must follow the following: a)Thread Safe. b)Source code must be provided. c)Development Environment Microsoft Visual Studio 6 must support for Standard C Library & Windows DLL. d)Makefile for Linux/Unix compile & build must be provided. 3) Complete ownership and distribution copyrights to all work purchased. Serial Comm Standard C Library & MS Windows DLL software developer will quit complete ownership and distribution copyrights for the software and source code. ## Platform Serial Comm Standard C Library & MS Windows DLL 1) Be able to compile & build the Serial Comm Standard C Library in Target platforms Linux/Unix/MS Windows 2)Standard C Library & Windows DLL must follow the following: a)Thread Safe. b)Source code must be provided. c)Development Environment Microsoft Visual Studio 6 must support for Standard C Library & Windows DLL. d)Makefile for Linux/Unix must be provided.