Profile cover photo
You're now following
Error following user.
This user does not allow users to follow them.
You are already following this user.
Your membership plan only allows 0 follows. Upgrade here.
Successfully unfollowed
Error unfollowing user.
You have successfully recommended
Error recommending user.
Something went wrong. Please refresh the page and try again.
Email successfully verified.
User Avatar
$15 USD / hour
Flag of TURKEY
istanbul, turkey
$15 USD / hour
It's currently 12:13 PM here
Joined December 28, 2013
1 Recommendation

Dervis Y.

@cesur135

verified.svg
4.6 (32 reviews)
5.6
5.6
75%
75%
$15 USD / hour
Flag of TURKEY
istanbul, turkey
$15 USD / hour
85%
Jobs Completed
95%
On Budget
90%
On Time
5%
Repeat Hire Rate

electr.electronics &Cont.Automation&Software Eng.

I have worked on several projects in my working life. Especially in the area of industrial Automation ,I have worked on the Wastewater Treatment Plant and Water Treatment Plant Automation Project. I wrote the system software with the SIEMENS TIA Portal program and the Simatic Manager program according to the automation scenario and then I worked with the SIEMENS WinCC SCADA program to monitor and control the system. I used the SIEMENS PH & INFORMATION SERVER program to report the units on a monthly, monthly and yearly basis and prepared templates for the reports. I did (PTP) point to point tests and automation tests when the units were switched on. I drew the Electricity Projects with the E plan P8 V2.6 program. In the field of process automation, I used the DELTA PLC program and the ABB PLC program to control each piece of equipment in the factory. In Energy Automation, I also worked in HES projects where I made the generators PLC and SCADA system. Ventilation systems of plants and enterprises were made according to the temperature of the environment, according to the working information of the machines and according to other factors. Ventilation system entered the circuit and worked in a certain place. I usually used ABB AC500 PLC program and ABB & SIEMENS drivers when doing these systems. I install &Comission Chocolate Machines,lines.And test all equipment then commission about process follow. I used Honeywell DCS C200 in iron steel industry and I comissioned this systems about part by part units In the field of electricity, I work actively in the fields of electric panel works, electricity projects and field applications of small enterprises in general. I used OMRON PLC some factory application with given scenario I wrote plc to control each equipment and depend on sensor etc.. I set up on the field instruments, configuration upper and lower limit values during setup, setup analogue 4.20 mA, 0-10 V. I made work such as parameter setting of ABB & SIEMENS drivers and softstarters. In Machine Automation ,I have done projects like machine process Automation and writing software depositor and other part of machines and there I used AB PLC –RS Logix 5000 and Factory talk.

Contact Dervis Y. about your job

Log in to discuss any details over chat.

Portfolio

6655050
6655031
6655050
6655031

Reviews

Changes saved
Showing 1 - 5 out of 32 reviews
Filter reviews by:
5.0
₹56,250.00 INR
Understood the work and was prompt in communication
C Programming
Microcontroller
Embedded Software
PCB Layout
Embedded Systems
V
Flag of Aayushman G.
@VGsolar
4 months ago
5.0
€800.00 EUR
Extremely dedicated person, friendly and huge Siemens know-how.
Motor Control
PLC
Siemens NX
F
Flag of Flavio H.
@flaviologistik
4 months ago
5.0
$215.00 USD
Good worker with hi knowledge
Electronics
Microcontroller
PLC & SCADA
Electrical Engineering
PCB Layout
O
Flag of Omar T.
@omaraltimary
4 months ago
4.6
₹21,000.00 INR
Dervis is an expert in his field and clearly identifies and solves the given problem. He is also able to suggest improvements on the asked requirement. If you are looking for a PLC programmer, he would be a great fit.
Engineering
Electronics
PLC & SCADA
Electrical Engineering
PLC
G
Flag of Arun P.
@gunnerforlife52
8 months ago
0.0
$140.00 USD
The project is not completed according to the dispute
User Avatar
Flag of Ahmed A.
@AhmedKh97
9 months ago

Education

3.86

Gaziantep Üniversitesi, Turkey 2009 - 2014
(5 years)

Qualifications

PLC&SCADA

SIEMENS
2014
CERTIFICATE HAS BEEN TAKEN FROM SIEMENS

software

bilge adam
2013

java

netaş telecominication A.Ş
2013

Publications

wind trubine

sabah
wind tubine was designed by qualıty team

Contact Dervis Y. about your job

Log in to discuss any details over chat.

Verifications

Preferred Freelancer
Identity Verified
Payment Verified
Phone Verified
Email Verified
Facebook Connected
Previous User Next User
Invite sent successfully!
Thanks! We’ve emailed you a link to claim your free credit.
Something went wrong while sending your email. Please try again.
Registered Users Total Jobs Posted
Freelancer ® is a registered Trademark of Freelancer Technology Pty Limited (ACN 142 189 759)
Copyright © 2024 Freelancer Technology Pty Limited (ACN 142 189 759)
Loading preview
Permission granted for Geolocation.
Your login session has expired and you have been logged out. Please log in again.