Last seen: Jul 28, 2014 6:47 PM EDT
Hire Me!
Rate: $30.00 USD/hour
Follow Invite to Project

CanDo Inc.

Electronics design - from concept to reality

Username: Bulba39

  • Has not made a deposit.
  • Has verified their email address.
  • Has completed their profile.
  • Has verified their secure phone number.
  • Verified
  • Payment is not verified.

Location: Gold Coast, Australia

Member since: December 2010



(22 reviews)

[see more]

No user has recommended this freelancer.

My projects:

  • $55.50 USD
    Profile image for Seller igeorge5149


    Feb 24, 2014

    Very challenging project from start, involving detection of an adjustable threshold point and switch to backup battery.The challenge was that both batteries had the same voltage = 3 volts (2xAA and CR2032). The approach taken by the engineer is to set the threshold for switching at 1.6 volts (0.8V*2)Then use an ideal Oring diode made from mosfets to prevent the flow back on the dead battery (regular diode has high drop).They are chips like that made by only 3 companies Maxim outrageous expensive.Intersil no adjustable threshold and just 32mA maximum output.Linear Technology, expensive also.I am very pleased with the engineer job as just in the first half hour he comes up with the concept and working schematic.Due to my customer requests, we had to go many times back and forth to made changes as requested, but all the changes were just in adjusting the values of the original schematic.I highly recommend this engineer for any analog job (my project was analog).

    Project Description:I need a battery backup system for a system which run on 3 volts. Main supply 4.5 volts = 3 X AA , backup CR2032 = 3 volts non rechargeable The design shoud switch over when the main is down to 2.7 volts Do not use OR diodes - it does not work Do not use WEBench from TI...
  • $500.00 AUD
    Profile image for Seller Arniem


    Jun 16, 2013

    Top quality polished result. Accuracy is critical in the assembly of a 100+ pin breakout board. Understood my requirements and made sensible suggestions for improvements in the layout of the board. Carefully confirmed understandings when it was necessary. Looking forward to working on future projects.

    Project Description:Hi - would like to discuss your availability for a project I have been contemplating. The project is to build a breakout box/board which will sit between the Engine Control Unit (ECU) and wiring harness of my car...
  • $125.00 USD
    Profile image for Seller NewArm


    Feb 16, 2013

    Bulba39 is definately an A+ player that can deliver a successful project.

    Project Description:Major changes include: - 5 components removed (caps, crystal, hole) - 5 components added (caps, inductor) - power jack, rj45, sd card slot, and holes are slightly moved - power jack and lens holder...
  • $70.00 USD
    Profile image for Seller NewArm


    Oct 31, 2012

    Thank you for a job well done with exceptional quality<br/>

    Project Description:Move headers to designated area. Move associated components. Perform routing.
  • $420.00 USD
    Profile image for Seller NewArm


    Oct 5, 2012

    Great work. Delivers very professional work as always.

    Project Description:I need help with updating the PCB layout and routing using Altium Designer 10. - A number of components are removed - 10 new components are added (layout image is attached) - 6 components with new footprints - I also need footprints created for 2 components: ov7725 and YT080-B1150M12...
  • $300.00 USD
    Profile image for Seller spyker49


    Sep 2, 2012

    Good job. Understood the technical issues. Provided helpful suggestions

    Project Description:An Altium project. PCB layout rework job. 6 layer with a few 40A +20A tracks/layers and high density logic. Your rate is shown as $5 per hour: Is this correct?
  • $180.00 AUD
    Profile image for Seller bobb1


    Apr 30, 2012

    It was a pleasure to work with Bulba39

    Project Description:[This is a Private Project. You must be logged in to view the Project Description]
  • [Sealed]
    Profile image for Seller EconisLabs


    Apr 15, 2012

    He delivered the project on time and on budget. He was very knowledgeable and easy to communicate with. I would hire him for another project.

    Project Description:[This is a Private Project. You must be logged in to view the Project Description]
  • $180.00 USD
    Profile image for Seller sammyso


    Apr 6, 2012

    Bulba39 was knowledgeable, easy to work with, on time, professorial, and a fast worker. i will definitely be in contact in the future for further projects. great work thanks again.

    Project Description:hello, im looking for someone to design a pcb for me. i dont have much requirements, ill list them at the bottom. ill also need someone that has a good eye and can make suggestions. i have the control program already completed...
  • $220.00 USD
    Profile image for Seller AndyClayton


    Feb 25, 2012

    Very professional work. Went above and beyond my requirements.

    Project Description:We invite bids for the design of a simple battery powered electronics device with an alarm. The work we are looking for includes: Schematic design component specification (BOM) PCB layout (optional) Device description: Battery powered Motion sensor with audible alarm...
    CanDo Inc. has not completed any projects.
    CanDo Inc. does not have any work in progress.
  • $2000 USD Mar 2, 2014

    I want a breadboard for the Linux beagleboard xM.It&quot;s a simple board to connect peripherals (sensors and servos).It&quot;s just a prototype not aimed to be sold.The budget is 2000 USD max.My needs:- The board will be powered by a LiPo 6S. a DC plug will be used to power the beagleboard from the board.- the communication bus between the boards will be serial over USB.- the connection type on the daughterboard will be USB mini B.- the board will support the following peripherals:* 7 connectors to connect AX-12A servos; 3 front,2 back, 1 left, 1 right (cf -> product info ->dynamixel->ax12-A), The cables and 3 servos will be provided.* 6 connectors for 6 force sensors (2 front,2 back, 1 left, 1 right) (, One sensor will be provided* one connector for an IR sensor (, One cable and one sensor will be provided.* one IMU ( One sensor will be provided.* one laser ( One sensor will be provided.* one voltage monitoring ( One sensor will be provided.- You may provide a custom case. If not, the dimensions of the board must not exceed 9 x 10 cm.- The board will receive requests from the USB port to read sensor values.- The board will receive commands from the USB port to the servos. Problem: the AX bus is half-duplex.- You have to explain the protocol to communicate with the board.I would like to reuse the sensors for other projects, so tell me which you may weld on the board.Feel free to ask clarifications. We may have a live session if you need.Regards,Fabien

    CanDo Inc. does not have any open projects.
    CanDo Inc. does not have any work in progress.
[see more]


[see more]



Electronics Hardware Design Engineer

Jan 2002 - Present (12 years)


I have designed and developed many 8/32 bit micro-controller based electronics circuits, schematics & PCB layout for Silabs, PIC24s, MSP430s, Atmel AT91SAM7, M16C, STM32 CortexM3 ARM MCUs well as Cyclone, Actel FPGAs, DDR2 SDRAMs, high voltage and power electronics design.Low power and discrete transistor circuit design, isolated 10-150Wt AC-DC SMPS , non-isolated DC/DC converters, buck, boost, SEPIC. Peripherals USB,I2C,CAN,RS232-485,SPI,LVDS, SDRAM, EEPROM, MMC, JTAG,SATA<br /> I have huge experie


Bachelor Degree

University of Sydney





Journal of Applied Spectroscopy

Journal of Applied Spectroscopy