Achitech Shop Drawings need

Shop Drawings needed; Hello I have 2 projects that I need to have my architech drawing created into shop drawing for the project: Scope of work: Shop drawings created for 3 decks. I will provide all the architech drawing, sketch up drawings, and material. I need someone to take them and build the shop drawings, to include a revision on the initial material lists. Deck type: Ipe decking with Structural plastic lumber sub frame. Commercial building about 2700sqft of decking. Will Provide all PDF cad drawing for the project. ## Deliverables 1) All deliverables will be considered "work made for hire" under U.S. Copyright law. Employer will receive exclusive and complete copyrights to all work purchased. (No 3rd party components unless all copyright ramifications are explained AND AGREED TO by the employer on the site per the worker's Worker Legal Agreement). * * *This broadcast message was sent to all bidders on Wednesday Dec 1, 2010 5:16:29 PM: Hello Everyone; The project just got approved. and I need the drawings by 12/10/10. If you are still interested. Please post your bid. I will also offer expert guarantee and a bonus. I have more project lined up too. Here is the overview drawing. There is 3 deck in total. the one with the ramp is going to be a floating deck, the other is to be built on 3x10 SPL. All sub-supports are Structural Plastic Lumber, All hardware and brackets are Simpson. Everything gets a bracket. No toe nails. Thanks * * *This broadcast message was sent to all bidders on Wednesday Dec 15, 2010 7:51:34 PM: Hello I did all the scketch up today. So here is what I need. I need these turned digital, in a PDF cad file. Can you please do this. See attached photo of the drawings. I will try to get this scanned but I don't know if I can...Please review and call me when you get it. Ramp and Roof: As per drawings: Height of Decking: 6?? Sub frame: Floating Deck Breakdown of layering: 1) Floating shims .5-1.5 SPL sub frame: 3.5 inches Decking: 5/4??. Build with 4 Crossbeam 16?? off center running parallel with the outside of the deck. Blocking is place every 4’ on the whole length of the ramp. All Cuts, and connection must be stainless steel brackets. Structural Drawing Name: A8.49 Break out of Ramp and Design A2.32 Over view off Deck Ipe wood Deck Scope Roof Ramp Sketch: Side view, Sub-frame Roof Decking: Height of Deck 6?? Sub frame: Floating Deck, SPL Breakdown: Deck in build 16?? joists, off back wall (ramp entrance) blocking every 4 feet. Off edge. All All Cuts, and connection must be stainless steel brackets. Structural Drawing Name: A8.49 Break out of Ramp and Design A2.32 Over view off Deck Ipe wood Deck Scope Courtyard Deck: Sub frame of deck is build of 3X10 SPL support beams ran 4x every 6’. 2x8 Joists will run every 16?? of wall connection, Blocking will be placed every 4’. 3x10 beam will be connect directly to the cement with U hangers. Back wall will be connected by provide “L?? brackets, and bolts (not in PO). All 2x8 joist will be bracket to the SPL support beams and blocking by stainless steel brackets. Everything gets a bracket. Structural Drawing Name: Ipe wood Deck Scope S.502 Hardware details A1.7: Overview Drawing L.1.7 Overview Drawing The following drawings and coordination information are posted for your reference: • A1.7 ??" Enlarged Courtyard Plan • A2.32M ??" Partial Level 2 Floor Plan MOB ??" East • A5.34 ??" MOB South Wall Section F.5 • A8.48 ??" MOB Exterior Details • A8.49 ??" MOB Exterior Details at Level 2 Patio • G1.40 ??" Grid Reference Drawing • L1.2 ??" Layout Plans • L1.7 ??" Sections ??" Interior Courtyard • S2.20F ??" Structural Level G Foundation Plan Courtyard • S2.22E ??" Structural Level 2 Floor & Roof Framing Plan MOB ??" East • S5.02 ??" Structural Framing Details (See Detail 6 for MOB L2 Slab Step) • S5.04 ??" Structural Framing Details (See Detail 10 for MOB L2 Slab Step) • Substitution Request for SPL Framing • Wood Decking Specification ??" 061500 • RFI 443 Response ??" Ipe Wood Decking Scope Clarifications Material Build out List: Roof Deck: Product: Subframe: 2x4 SPL: 1372.70 Lineal Feet *** 20%: 1647.25 90 deg Brackets: 1152 *** 20%: 1382.40 Screws: *** 4 holes: 4608 *** 20%: 5529.60 ***6 holes: 6912 *** 20%: 8294.40 Surface: 5/4?? X 4?? Ipe decking: 1341.11 Sqft *** 20%: 1609.33 4425.67 Lf *** 3.3?? *** 20%: 5310.80 4224.50 Lf *** 3.15?? *** 20%: 5069.40 1?? X 6?? Ipe Cap 132.13 Lf *** 20%: 158.56 Screws: Per Tiger Claws Kit Ramp Deck Sub frame: 387.20 Lineal Feet *** 20%: 464.64 90 deg brackets: 184 *** 20%: 220 Screws: *** 4 holes: 736 *** 20%: 956.80 *** 6 holes: 1104 Surface: 5/4?? X 4?? Ipe decking: 404.15 Sqft *** 20%: 484.99 1333.70 *** 3.3?? *** 20%: 1600.44 1285.20 *** 3.15?? *** 20%: 1542.24 1??X6?? Ipe Cap: 149.60 *** 20%: 179.52 Screws: Per Tiger Claws Kit Court Yard: Subframe: 3x10: 219 Lineal feet *** 20%: 262.80 ABU33: 26 *** 20%: 32 “L?? brackets 8 *** 20%: 10 Bolts 16 *** 20%: 20 3x3x8 Brackets 48 *** 20%: 58 Srews *** 6 holes: 288 *** 20%: 345.60 2x8x16: 40 counts or 640 Lineal feet *** 20%: 48 Count or 768 lf 2x8x24: 220 Lineal feet *** 20%: 264 Ft 2x8 Brackets: 266 *** 20%: 320 Surface: 5/4?? X 4?? Ipe Decking: 854.85 Sqft *** 20%: 1925.81 2821.1 *** 3.3?? *** 20%: 3385.22 2692.78 *** 3.15 *** 20%: 3231.34 1??X6?? Ipe Cap: 195.80 Lineal Feet *** 20%: 234.96 Screws: Per Tiger Claws Kit ## Platform Cad, PDF